Weixin Wang

Dr. Weixin Wang

Tianjin University, Tianjin, China

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 June 2023 in Ceramics International
Verified
Journal Article
Closed access
QHQinghua Han
Qinghua Han
AWAn Wang
An Wang
WWWeixin Wang
Weixin Wang
JZJinrui Zhang
Jinrui Zhang

13 July 2024 in Construction and Building Materials
Verified
Journal Article
Closed access
WWWeixin Wang
Weixin Wang
QHQinghua Han
Qinghua Han
QCQiang Cao
Qiang Cao
JXJie Xu
Jie Xu

3 October 2022 in Buildings
Verified
Journal Article
Open access
PDF file
MSMing SUN
Ming SUN
YFYin Fu
Yin Fu
WWWeixin Wang
Weixin Wang
YYYouzhi Yang
Youzhi Yang
AWAn Wang
An Wang
This paper experimentally studied the effects of different molybdenum tailings (MoT) content, standard curing and 60 °C water curing conditions on the compressive strength of fly ash-based geopolymers at different ages. X-ray diffraction (XRD), scanning electron microscopy/energy dispersive spectrometer (SEM/EDS) and Fourier-transform infrared spectroscopy (FTIR) were applied to investigate the effect of the content of MoT and different curing conditions on the reaction products, microstructure and chemical composition of fly ash-based geopolymers. The results show that MoT content and curing conditions have synergistic effects on the compressive strength of fly ash-based geopolymers. For standard curing, the increase in MoT content is detrimental to the development of compressive strength, and an obvious weak interfacial transition zone between MoT and the gel product is observed in specimen containing 40 wt% MoT; meanwhile, under water curing conditions, the compressive strength of geopolymers first increases and then decreases with the increase in MoT, and the 28-day compressive strength can reach 90.3 MPa when the content of MoT is 10 wt%. The SEM results show that the curing conditions have a great influence on the microstructure of the geopolymer matrix, and the microstructure of the specimens under the water curing conditions is smoother and denser, with fewer pores. EDS analyses show that the gel product constituting the geopolymer matrix is N(C)-A-S-H gel; MoT can participate in the reaction, and the mass ratio of Ca/(Si + Al) of N(C)-A-S-H gel increases with the increase in MoT, resulting in a decrease in compressive strength. In addition, the results of the FTIR confirm that water curing can increase the degree of crosslinks in the gel phase.

20 July 2023 in Journal of Building Engineering
Verified
Journal Article
Closed access
WWWeixin Wang
Weixin Wang
QHQinghua Han
Qinghua Han
Jie XuJie Xu
Jie Xu
QCQiang Cao
Qiang Cao
YCYaoshuo Chang
Yaoshuo Chang

12 November 2024 in Construction and Building Materials
Verified
Journal Article
Closed access
Jie XuJie Xu
Jie Xu
QCQiang Cao
Qiang Cao
WWWeixin Wang
Weixin Wang
YLYihang Liu
Yihang Liu

1 June 2022 in Journal of Industrial Textiles
Verified
Journal Article
Open access
QFQianqian Fang
Qianqian Fang
LCLi Chen
Li Chen
WWWeixin Wang
Weixin Wang
CZChanglong Zhang
Changlong Zhang
Ply splicing design is a crucial technology to realize the precise manufacturing of woven composite components with various complex shapes. This paper reports two ways of splicing, inter-layer splicing, and in-plane splicing. Two factors affecting the tensile properties of carbon fiber/epoxy laminated woven composites with ply splicing are discussed, including the number of continuous fabric layers on the surface and in-plane splicing spacing. The deterioration of the composites induced during the tensile test is characterized by acoustic emission and digital image correlation. The results reveal that the damage of the laminated woven composites with ply splicing occurs mainly at the butt jointing location and leads to fracture failure. Ply splicing has little effect on the tensile modulus of the composites. The tensile modulus is slightly reduced between 2% and 5%. But ply splicing has a more significant effect on its tensile strength. The total number of continuous fabric layers at the splice position approximately determines the strength retention ratio. The more the number of continuous fabric layers on the surface are, the higher the tensile strength of the composites. When the number of continuous fabric layers on the surface is three layers, the tensile strength retention ratio reaches 69%. The larger the splicing spacing is, the better the tensile properties of the composites. When the splicing spacing is increased to 30 mm, the tensile strength retention ratio reaches 77%.