European Directive 2007/60/EC only briefly mentions the problem of hazard arising due to groundwater flooding, and techniques for the mapping of hazard occuring due to rising groundwater have not yet been scientifically developed. The groundwater‐related threats that occur during floods may include concentrated leakage of groundwater behind levees, heave, or potential uplift of the topsoil layer at the protected area. The hazard corresponding to rising groundwater level depends on a number of factors related to the flood course, groundwater regime, geology, and topology of the protected area. The limit state approach is applied to the assessment and mapping of hazard induced by rising groundwater level in the area behind flood protection barriers, and the contributing factors are discussed, quantified, and incorporated into the limit state condition for topsoil layer uplift (UPL). An over‐design factor is expressed as a function of the spatial co‐ordinates (x, y). Data from geological and hydrogeological surveys and groundwater flow modelling are used to evaluate individual terms in the limit state condition. Uncertainties in the input data are expressed via partial factors. Data collection and their geographic information systems analysis completed with hydraulic modelling are crucial techniques in the hazard mapping of potential UPL during floods. The article includes a case study featuring a flood protection scheme for a shopping centre in the city of Brno, Czech Republic.
Flood-related issues include the impact of groundwater on flood protection measures and other subsurface structures in a protected area. At the same time, subsurface elements of flood protection structures may significantly influence the natural groundwater regime and affect existing structures during non-flood periods. The paper provides an overview of hazardous factors linked to groundwater and specifies variables for the quantification of related hazards. Appropriate hydraulic groundwater flow models are presented and discussed, and their suitability for the modelling of individual typical problems and for hazard quantification is specified. The use of models and the application of CAD and GIS tools for data pre- and post-processing is mentioned in brief and demonstrated on examples of typical practical situations.
Levees are the most frequently used flood protection measure worldwide. In central Europe, they have been built systematically since the beginning of the 19th century. After the extreme regional floods in 1997, 2002 and 2013, the need arose for a more systematic and optimised approach to levee design and management, including the decommissioning of ineffective dike reaches. In this paper, a multicriterial algorithm is presented for the optimisation of levee management. The aspects considered are flood risk, economy, technical conditions, environmental issues and the consistency with general documents and principles in water management. The method is demonstrated via a case study of a levee subsystem in the upper Morava River basin.
For open channels significant pollution sources during the intensive precipitations are outflows from storm-water overflows on the sewer network. When combined with low discharges in rivers, the water released from overflows can cause high concentration of pollution in receiving open channels. In this paper, the results of computer modeling of the impact of storm-water overflows on the stream water quality in three municipalities in Czech Republic are shown. The local river networks are the main receivers in the cities where storm-water overflows are led in. The results serve as a base for the proposals on the measures, improvements and structural modifications.
10 August 2023 in Journal of Hydrology and Hydromechanics
The modelling of solid transport in open channels requires good knowledge about parameters related to basic processes such as hydrodynamic dispersion, advection and decay rates. Such parameters are usually determined by dye tests. Numerous tracer studies have been performed on laboratory flumes and natural rivers. However, on-site sampling is often difficult, expensive and needs special apparatus. The main aim of the study was to justify simplified method based on the monitoring of the dye cloud shape in order to determine both longitudinal and transversal dispersion coefficients. In this study, four dye tests were carried out on a small local stream (the Lipkovsky) using Rhodamine WT fluorescein dye as a tracer. The tests were carried out in such a manner that both longitudinal and horizontal transversal dispersion data were obtained. For this purpose, the visually determined extent of the dye cloud was interpreted via the analytical solution of the advection-dispersion equation. The results obtained by this simplified approach indicated that the longitudinal dispersion coefficient Dx = 0.051–0.057 m2/s and the coefficient of horizontal transversal dispersion Dy = 0.00024–0.00027 m2/s. The method was justified by corresponding root mean square error (RMSE) counting RMSE = 0.65–1.02 m for the dye cloud centre, RMSE = 1.87–2.46 m for the head and tail of the cloud and RMSE = 0.025–0.11 m for the cloud width, the Nash-Sutcliffe efficiency coefficients ranged from 0.9 to 0.998. The comparison of these values with empirical formulae and other tracer studies indicated significant overestimation of the mentioned values of Dx, which can be attributed to the uniform velocity distribution along the width of Lipkovsky Stream. Much better agreement was achieved for Dy.