Successful exploitation of carbonate reservoirs relies on the acid-fracturing process, while the thickeners used in this process play a key role. It is a common engineering problem that thickeners usually fail to function when used in high-temperature environments. Until now, no research has ventured into the field of synthesizing thickeners which can be effectively used at ultra-high temperatures up to 180 °C. In our current study, a novel high-temperature-resistant polyacrylamide thickener named SYGT has been developed. The thermal gravimetric analysis (TGA) reveals that SYGT is capable of withstanding temperatures of up to 300 °C. Both our scanning electron microscopy (SEM) and rheological analysis demonstrate that the SYGT exhibits excellent resistance to both temperature and shear. At 180 °C, the viscosity of the SYGT aqueous solution is no lower than 61.7 mPa·s at a 20% H⁺ concentration or high salt concentration, and the fracture conductivity of the thickened acid reaches 6 D·cm. For the first time, the influence of the polymer spatial network’s structural parameters on the viscosity of polymer solutions has been evaluated quantitatively. It was discovered that the length and surrounding area of the SNS skeleton have a synergistic effect on the viscosity of the polymer solution. Our experiments show that SYGT effectively reduces the acid–rock reaction rate and filtration loss under harsh working conditions such as high temperature, strong shear, high salinity, and a high concentration of acid. The synthesized acid-fracturing thickener (SYGT) has wide application potential in the development of carbonate reservoirs under high-temperature conditions.

Most of the onshore water-flooding oilfield reservoirs have dominant seepage channels dominated by large pores and fractures, resulting in the oilfield being in a period of high water cut. The treatment of this problem needs to be solved by plugging. In the research process, the particle size and suspension of the water-swellable rubber particles were measured, and the effective time of the particles was evaluated; matching relationship. The results show that adding 2000 mg/L polymer to the water-swellable rubber particles can better improve the suspension performance; the performance of the polymer solution will not be affected during mixing and injection. In addition to strong swelling performance, it also has a certain strength and deformability, up to 10 MPa high via pressure and good thermal stability. Compared with the water and oil environment, the chemical degradation phenomenon is significant after soaking in alkaline conditions. Compared with the alkaline environment and the formation water environment, the final expansion ratio of the water-swellable rubber particles in the formation oil environment is as low as 2.5 times, which has the ability to block water. There was no oil blocking feature. When the crack width is too small, particles with excessively large particle sizes may accumulate at the injection end of the core, resulting in failure to inject into the core and fail to achieve the plugging effect. For the treatment of large, fractured pores, it is possible to first inject particles with a particle size of 0.250–0.420 mm to block areas with high permeability, and then inject particles with a particle size of 0.150–0.250 mm to block areas with low permeability.

Radial drilling-fracturing is an innovative fracturing technology that achieves superior stimulation effects. In order to study the permeability-increasing effect and main influencing factors of radial water jet drilling in the low physical section, this paper uses a fracking electrical simulation experiment, based on the principle of hydropower similarity, to simulate the reservoir conditions and well pattern in the low physical section and, at the same time, establishes the radial fracturing model of the low physical section reservoir, simulates the saturation field, pressure field, and production-change law under different drilling parameters, and studies different influencing factors. The experimental results show that when the number of drilling holes exceeds two, the effect of increasing production gradually becomes less significant as the number of drilling holes increases; Within the range of the angle between the two boreholes, the forward distance of the oil–water displacement front is the farthest and the sweep is relatively uniform. On both sides of the included angle, the forward distance of the oil–water displacement front edge is smaller than the forward distance of the displacement within the included angle range and it is clearly inclined towards the radial drilling with uneven spread. Radial drilling has an impact on the seepage field, causing changes in its streamline. The pressure inside the borehole is lower than the surrounding formation pressure and most of the flow lines change direction near the borehole location, causing deflection. As the borehole length increases, the oil-well production also increases. The optimal effect is for the borehole length to be 100 m. This study provides a reference for the on-site application of radial fracturing in low physical properties sections.