For the management of fractured large pores in high-water-bearing reservoirs, the general approach is to use transfer dissection and sealing. Conventional regulators have a limited regulating radius and can only produce blocking in the near-well zone, which is not ideal. Deep dissection technology can expand the radius of action and substantially improve the blocking effect. The existing deep-dissection agent system has problems such as high cost and poor effect, which affect its large-scale application. In this paper, to address these problems, a gel-type dissection modifier cross-linking agent was synthesized and optimized in the laboratory using low-concentration polymer, and the factors affecting the final gel formation effect were experimentally studied. The final polymer concentration was chosen to be 1500 mg/L~3000 mg/L, the poly-crossing ratio was 30:1, the pH was controlled at 7–9, and the temperature was controlled at 30–60 °C; the rubber was formed with good shear resistance and thermal stability, and had good adaptability to the high-mineralization environment. The optimal injection concentration of water-expanded rubber particles for this system was confirmed to be 3000 mg/L. Cryo-electron microscopy was used to observe the morphology of polymer gel formation and the adhesion of nucleated water-expanded particles to the gel, to clarify the mechanism of enhanced retention and sealing of nucleated water-expanded rubber particles by the multiple complex gel system, and finally to verify the sealing performance of the composite sealing system and determine the use effect by indoor simulation experiments with a two-dimensional flat plate model. This study is of great significance for the efficient development of high-water-bearing late reservoirs and further improvement of crude oil recovery.

Most of the onshore water-flooding oilfield reservoirs have dominant seepage channels dominated by large pores and fractures, resulting in the oilfield being in a period of high water cut. The treatment of this problem needs to be solved by plugging. In the research process, the particle size and suspension of the water-swellable rubber particles were measured, and the effective time of the particles was evaluated; matching relationship. The results show that adding 2000 mg/L polymer to the water-swellable rubber particles can better improve the suspension performance; the performance of the polymer solution will not be affected during mixing and injection. In addition to strong swelling performance, it also has a certain strength and deformability, up to 10 MPa high via pressure and good thermal stability. Compared with the water and oil environment, the chemical degradation phenomenon is significant after soaking in alkaline conditions. Compared with the alkaline environment and the formation water environment, the final expansion ratio of the water-swellable rubber particles in the formation oil environment is as low as 2.5 times, which has the ability to block water. There was no oil blocking feature. When the crack width is too small, particles with excessively large particle sizes may accumulate at the injection end of the core, resulting in failure to inject into the core and fail to achieve the plugging effect. For the treatment of large, fractured pores, it is possible to first inject particles with a particle size of 0.250–0.420 mm to block areas with high permeability, and then inject particles with a particle size of 0.150–0.250 mm to block areas with low permeability.

Many onshore oil fields currently adopt water flooding as a means to supplement reservoir energy. However, due to reservoir heterogeneity, significant differences in permeability exist not only between different reservoirs but also within the same reservoir across different planar orientations. After prolonged fluid flushing in the near-wellbore zone of injection wells, the resulting increased flow resistance between layers exacerbates inefficient and ineffective circulation. A considerable amount of remaining oil is left unexploited in untouched areas, significantly impacting the overall recovery. To investigate the multiscale plugging mechanisms of fracture-dominated pore channels in high-water-cut oil reservoirs and achieve efficient management of fractured large channels, this study explores the formation of the fracture-flushing zone-low saturation oil zone. A physical experimental model with fractures and high-intensity flushing is established to analyze changes in pore structure, mineral composition, residual oil distribution, and other characteristics at different positions near the fractures. The research aims to clarify the mechanism behind the formation of large channels with fracture structures. The results indicate that under high-intensity water flushing, cementing materials are washed away by the flowing water, clay particles are carried to the surface with the injected fluid, and permeability significantly increases, forming high-permeability zones with fracture structures. In the rock interior away from the fracture end, channels, corners, and clustered oil content noticeably decrease, while the content of film-like oil substantially increases, and clay minerals are not significantly washed away. Under strong flushing conditions, the number of residual clay particles near the fracture end is mainly influenced by flow velocity and flushing time; thus, the greater the flushing intensity, the faster the water flow, and the longer the flushing time, the fewer residual clay particles near the fracture end.