Solar energy production and economic evaluation are analyzed, in this study, by using daily solar radiation and average temperature data which are measured for 3 years in the Osmaniye province in Turkey. Besides, this study utilizes the photovoltaic- (PV-) based grid connected to a power plant which has an installed capacity of 1 MW investment in electricity production. Economic values show that the net present value (NPV), the first economic method in the research, is about 111941 USD, which is greater than zero. Therefore, the payback year of this investment is approximately 8.3. The second one of these methods, the payback period of the simple payback period (PBP), is 6.27 years. The last method, which is the mean value of the internal rate of return (IRR), is 10.36%. The results of this study show that Osmaniye is a considerable region for the PV investment in electricity production. As a result, investment of a PV system in Osmaniye can be applicable.
1 October 2016 in International Journal of Heat and Fluid Flow
The aim of the present study is to investigate the experimental performance of a solar dryer by using a novel type of a drying chamber for increasing the drying performance and ensuring homogeneous drying. The drying system (SDS) consisted of a new type of a drying chamber and a solar air collector, which were designed, made, and tested in Osmaniye, Turkey. The analyses of Computational Fluid Dynamics were carried out to demonstrate the advantage of the designed drying chamber over the tunnel type drying chamber, which is commonly used in peanut drying. The drying experiments were conducted using in-shell peanut to observe the performance of the system. The drying procedure was performed in the form of open sun drying (OSD), and the results of drying kinetics such as moisture ratio (MR), drying rate (DR), and heat transfer coefficient (hc) obtained from both drying methods were compared. The MR and DR values obtained during the drying experiments were estimated using different models such as mathematical, multiple linear regression (MLR), decision tree (DT), and the support vector machine (SVM). It was observed from the numerical results that the products can dry more homogenously and effectively with the newly designed drying chamber compared to the conventional tunnel type drying chamber. The results of the drying experiments showed that the products dried earlier and more regularly through the SDS compared to the OSD. The DR and hc values were found 0.0051E-01 (gw/gdm)/min and 1.5727 W/m2°C for SDS and 0.0039E-01 (gw/gdm)/min and 1.4664 W/m2°C for OSD, respectively. The models that best estimated the experimentally obtained MR and DR values for peanuts dried with the SDS proved to be the Random Tree Model (R2 = 0.9972) and Quintic Model (R2 = 0.8551), respectively.
In this study, the visualization of the flow structure around a circular cylinder was investigated with dye injection experiments. The experiments were carried out in the closed-circuit open water channel in Osmaniye Korkut Ata University. Experiments have been studied on a circular cylinder at different rotational speeds. Experiments were carried out at Re = 1000 according to cylinder diameter and free stream velocity. In the study, with the increase of the rotation speed, an acceleration layer occurs between the fluid velocity in the cylinder wake in the flow direction and the flow from the circumference of the cylinder and the speed of rotation. This situation caused the complete disappearance of the vortex ruptures in the flow direction and the emergence of Kelvin Helmhotz fluctuations. As a result of the study, it is seen that the flow control is insufficient at low rotational speeds, but the flow can be controllable at high rotational speeds.
10 May 2016 in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
The present experimental work investigates the near surface flow structure and aerodynamic characteristics of X-45 type non-slender delta wing planform using dye visualization, Stereoscopic Particle Image Velocimetry (stereo-PIV) and aerodynamic load measurements. The instantaneous images are acquired on the plan-view plane within 5o ≤ a ≤ 20o to calculate the time-averaged flow data. In order to compare flow structures with other non-slender wing planforms such as delta and lambda, previously presented dye visualization and stereo-PIV results are also provided. It can be concluded that vortical flow with a pair of well-defined LEVs over X-45 develop at very low angles of attack, and form close to the wing surface similar to delta and lambda planforms. The stall occurs at an angle of attack a = 32o, whereas stalling is evident at relatively lower angles of attack for simple delta wing.
Excessive heating of electronic equipments may cause both decreasing thermal performance of system and undesirable consequences such as increased thermal stresses and mechanical defects in the system. In the literature, there are many studies including applications of thermal analysis and technologies in order to make cooling more effective. In this study, flow and heat transfer are investigated numerically in the case of three dimensional, incompressible, fully developed and laminar flow for semi spheres placed as multiple serials in a channel. The continuity, Navier-Stokes and energy equations are solved numerically by using Ansys Fluent-17.0 software program. Air is taken as working fluid. Inlet temperature of the air and sphere surface temperatures are 300 K and 350 K, respectively. The effects of location of semi spheres as multiple serials, placement angle and positions of sphres according to each other on the pressure drop and heat transfer enhancement for case of different Re numbers (Re=100, 200, 400 ve 800) are researched. The obtained results show that the positions of spheres have a great importance in the case of placement as multiple serials of semi spheres.