The on‐chip optical power splitter is a common and important device in photonic integrated circuits (PICs). To achieve a low insertion loss and high uniformity while splitting the guided light, multi‐mode interferometer‐based structures utilizing a self‐imaging principle are widely used mainly in the form of a 1 × 2 configuration. Recently, an inverse design method for nanophotonic devices has emerged to overcome the limited capability of the conventional design methods and make it possible to explore the vast number of design parameters. Because of the non‐intuitive shape of inverse‐designed structures, they allow us to discover interesting and complex optical responses which are almost impossible to find with conventional design methods. Here, we report two kinds of inverse‐designed 1 × 4 optical power splitters composed of silicon bars of different lengths, which are fabricated with a standard CMOS‐compatible process. The particle swarm optimization method was used to minimize the insertion loss and divide the power evenly into each output port with finite‐difference time‐domain method simulation. The first optical power splitter has a compact size of 8.14 × 12 μm 2 and the second optical power splitter has an even more compact size of 6.0 × 7.2 μm 2 . With the inverse designed structures, we fabricated the chip with a CMOS‐compatible fabrication process. Experimental verification of the structures is provided and good agreement with the numerical results is obtained. The first 1 × 4 optical power splitter has a low insertion loss of less than 0.76 dB and uniformity of less than 0.84 dB, and the second more compact optical power splitter has a low insertion loss of less than 1.08 dB and uniformity of less than 0.81 dB. As the complexity of on‐chip photonic systems has steadily increased, the inverse design of photonic structures holds great potential to be an essential part of advanced design tools.
Once light is coupled to a photonic chip, its efficient distribution in terms of power splitting throughout silicon photonic circuits is very crucial. We present two types of 1 × 4 power splitters with different splitting ratios of 1:1:1:1 and 2:1:1:2. Various taper configurations were compared and analyzed to find the suitable configuration for the power splitter, and among them, parabolic tapers were chosen. The design parameters of the power splitter were determined by means of solving inverse design problems via incorporating particle swarm optimization that allows for overcoming the limitation of the intuition‐based brute‐force approach. The front and rear portions of the power splitters were optimized sequentially to alleviate local minima issues. The proposed power splitters have a compact footprint of 12.32 × 5 μm 2 and can be fabricated through a CMOS‐compatible fabrication process. Two‐stage power splitter trees were measured to enhance reliability in an experiment. As a result, the power splitter with a splitting ratio of 1:1:1:1 exhibited an experimentally measured insertion loss below 0.61 dB and an imbalance below 1.01 dB within the bandwidth of 1,518–1,565 nm. Also, the power splitter with a splitting ratio of 2:1:1:2 showed an insertion loss below 0.52 dB and a targeted imbalance below 1.15 dB within the bandwidth of 1,526–1,570 nm. Such inverse‐designed power splitters can be an essential part of many large‐scale photonic circuits including optical phased arrays, programmable photonics, and photonic computing chips.
We demonstrate two-dimensional beam steering through wavelength control using a one-dimensional optical phased array (OPA) in which a path difference is built up in each channel to allocate a phase delay sequentially. Prior to the beam steering through wavelength tuning, phase initialization was performed to form a single beam using electro-optic p-i-n phase shifters to compensate for the phase error due to fabrication imperfections. With a 79.6 μm path difference in the phase-feeding lines and a 2 μm pitch in the grating radiators, we achieved a continuous transversal steering of about 46° through a wavelength tuning of about 7 nm. By extending the wavelength tuning range to 90 nm, longitudinal steering was attained near 13° with a discrete interval of about 1°. The beam was maintained during full two-dimensional steering and experienced only a small degree of degradation in the beam divergences and in the side lobe level. We analyzed the parameters to be able to induce the degradation of beam quality considering the fabrication errors of the geometric parameters of the OPA. The results indicated that the scanning scheme employing wavelength tuning after initialization with phase shifters can greatly reduce the realignment process of the beam pattern, even in the presence of some effective index perturbation during the fabrication.