Based on the JK Drop Weight test and principle of selective crushing, a multicomponent complex ore with its component minerals, i.e., pyrrhotite, sphalerite, and quartz, was used to explore the impact crushing characteristics and relationship between the complex ore and its component minerals. Results show that the order of impact crushing resistance is quartz > pyrrhotite > ore > sphalerite. The particle-size-distribution characteristic curve of ore crushing products is always “sandwiched” between the curves of pyrrhotite, sphalerite, and quartz within the same feed-size range. When the particle size is −63 + 53, −45 + 37.5, −31.5 + 26.5, and −22.4 + 19 mm, the component mineral pyrrhotite has a negative effect on the impact crushing of ore, while the component mineral sphalerite has a positive effect. When the particle size is −16 + 13.2 mm, the component mineral pyrrhotite has a positive effect on the crushing effect of the ore, while the component mineral sphalerite has a negative effect. The component mineral quartz always has a negative effect on the impact crushing effect of ore in all the studied particle sizes.
Most grinding operations are the process of reducing the particle size of ore materials under the combined action of impact and abrasion. The action mechanism of impact damage and abrasion damage of materials in the grinding process is different, and the ability of each constituent mineral of ore to resist impact damage and abrasion damage is different. In order to study the independent action mechanism and interaction law of impact and abrasion in grinding, mineral ores calcite, chalcopyrite, and sphalerite are studied in this paper. The JK drop weight test method and batch grinding test method are used to study the changes and laws of various indexes of three mineral ores under a single impact condition, a single abrasion condition, and the coexistence of the two effects. The results show that the impact crushing parameters of the three mineral ores and the corresponding hardness grade of the ores are related to the particle size. The smaller the particle size of the material, the smaller the value of the impact crushing capacity parameter A × b. The order of impact crushing resistance of the three mineral ores is consistent with the characterization results of ore Mohs hardness. Under the same particle size condition, the order of impact crushing parameter A × b of the three mineral ores is calcite > sphalerite > chalcopyrite. The first-order linear model can better fit the grinding kinetics in the cascading state, and its kinetic parameters are related to ore hardness and feed particle size. The t10 is more suitable to characterize the grinding effect in the dropping state than in the cascading state.
The relationship between the grinding characteristics of polymetallic complex ore and its component minerals, pyrrhotite, sphalerite, and quartz, under the action of abrasion was studied, based on batch grinding experiments and theoretical analysis methods of selective grinding. The results show that when the polymetallic complex ore was subjected to the action of abrasion, the crushing effect of ore was enhanced by the existence of sphalerite, that is, sphalerite plays a positive role in the crushing effect of ore. The crushing effect of ore was reduced by the existence of pyrrhotite and quartz, that is, pyrrhotite and quartz plays a negative role in the crushing effect of ore. In addition, the sphalerite had a more prominent effect on the grinding characteristics of the ore. The grinding speed of ore and its component minerals decreased exponentially with the grinding time, and the instantaneous grinding speed of 0 min was negatively correlated with the feed sizes. The rapidly decreasing trend of the grinding speed reached the threshold when the grinding time reached 4 min. The results can provide some theoretical guidance for the study of grinding characteristics of multi-component complex ores in subsequent grinding process.
During the grinding process, the crushing of minerals mainly depends on the impact action of the grinding medium. Based on the JK drop weight test data of quartz and pyrrhotite and the research results of their impact crushing characteristic parameters, this paper calculates the specific crushing energy (Ecs) of mineral samples subjected to impact in a ball mill using the grinding medium motion theory and then calculates the cumulative particle size distribution under screening under any mesh size using the JK drop weight test method. On this basis, the breakage distribution function of mineral samples is calculated, and a selection function is obtained based on grinding experiments. Finally, using Matlab programming and function-fitting mathematical methods, as well as a particle size population balance dynamics simulation of grinding, the particle size distribution characteristics of the grinding products of the two mineral samples in the mill that are only subjected to impact action are calculated. The results show that the selection function of quartz and pyrrhotite decreases overall with the prolongation of the grinding time, and the selection function of the coarse particle size changes more significantly than that of the fine particle size. At the same time, the selection function decreases with the decrease in feed particle size, and the smaller the feed particle size, the lower the probability of impact crushing. The Ecs values of quartz and pyrrhotite at each particle level in the mill are different, and the degree of mineral crushing is closely related to the impact energy, feed particle size, and mineral properties.
Based on batch grinding method and normalization idea, a conical ball mill is used and a quantitative separation method of grinding characteristics of multi-component complex ore is proposed. The results show that the feed sizes of polymetallic complex ore have an obvious influence on the particle size distribution of intermediate grinding products in the early stage of grinding. However, the influence of the feed size is relatively insignificant on the particle size distribution of intermediate grinding products in the middle and late grinding stages. The grinding product t10 is negatively correlated with the feed sizes of ore when the grinding force is applied to the ore. At the same time, it has a simple positive linear relationship with the grinding time. The contribution rates of component minerals pyrrhotite, sphalerite and quartz to the grinding characteristics of the ore are 28.64%~37.74%, 39.93%~51.84%, 16.07%~28.39%, respectively. Therefore, the order of contribution of component minerals to the grinding characteristics of ore is sphalerite > pyrrhotite > quartz. The results provide new insights for the subsequent study of grinding characteristics of multi-component complex ores.
Cassiterite polymetallic sulfide ore exhibits a complex mineral composition and significant variations in mineral properties, which frequently lead to issues such as the over-grinding of cassiterite and under-grinding of sulfide minerals during the grinding process. These issues consequently impair liberation performance in subsequent beneficiation stages. Among these factors, the grinding media ratios stand as one of the critical factors influencing grinding efficiency. Based on these, the paper adopts the single-factor test method to systematically study the influence law of factors such as grinding time, mill rotational rate, and mill filling rate on the particle size composition of ore grinding products and the grinding technology efficiency under different media conditions; in addition, it is compared with the influence law of different conditions of media ratios on the grinding efficiency of ore. The results show that the optimal parameters of the grinding operation are obtained at the grinding time of 4 min, the mill rotational rate of 60%, and the filling rate of 35%. The grinding time and mill filling rate have a relatively more significant effect on the product particle size distribution, while the effect of the mill rotational rate is relatively less significant. When the parameters of grinding operations are optimal, the yield of qualified particle size and grinding technical efficiency are used as the evaluation indices, respectively. Overall, the order of the grinding effect of different media conditions was as follows: steel ball combination of Φ20 mm and Φ25 mm > steel balls of three single sizes > steel ball combination of Φ20 mm and Φ30 mm. The optimal grinding media ratios are Φ20 mm and Φ25 mm (the percentage of the Φ20 mm ball is 90%). The reasonable media ratios will effectively coordinate the optimal grinding effect between different media. The research results can provide the necessary basic data for the subsequent grinding optimization of cassiterite polymetallic sulfide ores.