In order to clarify the temporal and spatial changes in the internal photothermal environment in an open-field agrivoltaic system (OAVS), this paper took the OAVS in eastern China as the research object and divided the internal area into the southern area, middle area and northern area, according to the spatial structure. Further, a photothermal environment test was conducted in the above three areas in the summer and winter. The results showed that the summer average daylight rate (R_m-avg) in the middle area was 66.6%, while the R_m-avg in the other two areas was about 20%, with no significant difference. In the winter, the light environment in the southern area was slightly better, and the R_m-avg in the above three areas was 26.4%, 24.7% and 19.7%, respectively. On the whole, the relationship between the thermal environmental factors and the solar radiation intensity was consistent. Further, a 3D model of an OAVS was established using Autodesk Ecotect Analysis 2011, and the internal light environment was simulated. Compared with the measured values, the relative error was less than 10%, which verified the reliability of the OAVS model. Then, the model was used to reveal the temporal and spatial changes in the light environment of the OAVS. The simulation results showed that the daylighting rate in the summer from the ground to the height of the fig canopy inside the system was 20.7% to 61.5%. In the winter, the daylighting rate from the ground to the height of the fig canopy inside the system was 17.7% to 36.4%. The effectiveness of the OAVS in reducing the level of solar radiation intensity depended on the time of day and the angle of the sun. At the spatial scale, due to the strong consumption of light by photovoltaic panels, there was a strong horizontal and vertical light environment gradient inside the system. In conclusion, the photothermal environment research of an OAVS based on Autodesk Ecotect Analysis 2011 can not only provide a basis for agricultural production and structural design such as span, height and the laying density of PV panels, but also expand its application to regions with different latitudes and longitudes and specific climates.

The cutting device in the seedling grafting process was studied, which provided a reference for optimizing the structural parameters and working parameters of important shearing components in the seedling grafting line, thereby improving the performance of the cutting device. The dynamic cutting process of the cutting device was numerically simulated. The effects of four factors, the average cutting speed (X₁), the sliding angle (X₂), the cutting edge angle (X₃), and the cutter clearance (X₄) on the cutting force, were studied. The optimal combination of structural parameters and working parameters of the cutting device was determined. The simulation results showed that the sliding angle (X₂) and the cutting edge angle (X₃) affect the ultimate cutting stress. The average cutting speed (X₁) and the cutter clearance (X₄) affect the ultimate cutting force. When X₁, X₂, X_3, and X₄ are 579 mm/s, 39°, 25°, and 1.4 mm, respectively, it is the better combination parameter, and the ultimate cutting equivalent stress of the cutting device is 0.32 Mpa. A high-speed cutting device for grafted seedlings was built, and the cutting experiment was carried out. The experiment results showed that the simulated values fit well with the experimental data. Under the optimal combination of cutting parameters, the cutting stress of the cutting device was smaller. The finite element simulation of the seedling grafting cutting device reduces the experiment cost and provides a reference for developing the seedling grafting line.

The modular heat storage wall is a new type of solar greenhouse wall structure, which has the advantages of fast construction and good heat storage ability. This study provides data reference and practical value for producing modular heat storage wall in the construction of a solar greenhouse. In this paper, we used different heat storage materials to construct the modular wall. In the winter thermal environment test, soil module solar greenhouse (SG) and stone module solar greenhouse (PG) were controlled against each other in two greenhouses. The test results for 28 consecutive days (31 January 2021 9:00 to 28 February 2021 9:00) showed that both greenhouses could effectively increase the temperature in greenhouse by 10–12 °C. The average temperature of SG was 0.86 °C lower than that of PG during the daytime (09:00–17:00) and 0.44 °C higher than that of PG during the nighttime (17:00–09:00). Under typical sunny conditions, the average temperature differences between the inlet and outlet of SG in the heat storage and exothermic stage was less than that of PG, and the relative humidity difference was greater than that of PG. This indicated that SG had a better performance of heat preservation than PG and could raise the nighttime temperature rapidly. Under the condition of a typical cloudy day, the average temperature difference between the inlet and outlet was SG < PG and the relative humidity difference was SG > PG in the exothermic stage, which was consistent with the conclusion of sunny days. In the storage and exothermic stages of typical sunny days and cloudy days, the total heat exchange of SG was 464.87, 110.44 and 54.82 MJ and the total heat exchange of PG was 264.16, 61.60 and 46.89 MJ, respectively. Moreover, the heat storage and release of SG were more than that of PG in all stages. In summary, the thermal performance of the modular heat storage wall heliogreenhouse could meet the growth of tomato crop, in which the heat transfer performance of SG was optimum.