Pesticide application by unmanned agricultural aerial vehicles (UAVs) has rapidly developed in China and other Asian counties. Currently, tank-mix spray adjuvants are usually added into pesticide solutions to reduce spray drift and facilitate droplet deposition and control efficacy. The currently used tank-mix adjuvants are all derived from conventional ground sprays, and their mechanisms of action in aerial applications are still unclear. In order to clarify the spraying characteristics and control efficacy of those adjuvants in aerial sprays, the performances of various types of tank-mix adjuvants were compared by analyzing droplet spectrum, drift potential index (DIX) in a wind tunnel, field deposition and control efficacy on wheat rust and aphids. The atomization results showed that the addition of adjuvants could change the droplet spectrum of liquid, and the results suggest that droplet size is an effective indicator of spray drift potential. In the field application, the meteorological conditions are complex and uncontrollable, and the effects of adjuvants on droplet deposition and distribution were not significant. Compared with the control solution, there was no significant difference in the deposition amount of each adjuvant solution, and the CVs of deposition were higher than 30%. Adding adjuvants to the spray solution can significantly improve the control efficacy of pesticides on wheat aphids and rust and also prolong the duration of the pesticide. Our results suggest that tank-mix adjuvants should be added when UAVs are used for aerial application. This study can be used as a reference to the research and development or selection of adjuvants in aerial sprays of UAVs.

Diseases and pests are important factors in vegetable cultivation; they not only affect the growth and appearance of vegetables but also affect the yield and quality. The disease and pest control of vegetables is dominated by chemical sprays, for now. As a result, the excessive use of pesticides has been a crucial factor of pesticides’ non-point source pollution, and it is also the main cause of excessive pesticide residues in vegetables. Therefore, the design of efficient plant protection machinery and technology has become an urgent demand in order to ensure the quality and safety of vegetables. In this review, the machinery and technologies for vegetable protection are introduced from the aspects of chemical control and physical control. In the aspect of chemical control, handheld sprayers, self-propelled or track sprayers, fixed-pipe spray systems, vertical and horizontal boom sprayers, unmanned aerial vehicles (UAVs) and vegetable seed treatment techniques are introduced. In the aspect of physical control, soil physical disinfection, pest trapping technologies and ozone sterilizers are introduced. Finally, the existing problems and perspectives of pesticide application sprayers and physical control equipment for vegetables are summarized. This paper can provide references for vegetable growers and researchers.

The effective quantification of deposition rate is of vital importance in optimizing the application performance and the utilization of pesticides; meanwhile, the canopies of fruit tree orchards are large, with dense branches and leaves shading each other, making it difficult to quantify spraying efficiency. Therefore, it is imperative to develop a facile methodology for assessing the performance of different spraying techniques in terms of distribution and utilization rate in orchards. To evaluate spraying efficacy in orchards, a canopy segmentation method was developed in to be able to determine the spray deposition rate. The distribution and deposition rate of spray liquid applied using three kinds of orchard sprayer were measured in a pear orchard and a peach orchard. The test results showed that the trailer sprayer had the highest deposition rates, with values of 31.54% and 56.92% on peach and pear trees, respectively. The deposition rates of the mounted sprayer in the peach and pear canopies were 21.75% and 40.61%, and the rates of the hand-held sprayer were 25.19% and 29.97%, respectively. The spray gun had the best droplet distribution uniformity, with CVs of the spray in the peach and pear canopies of 20.54% and 25.06%, respectively. The CVs in the peach and pear canopies were 35.98% and 26.54% for the trailer sprayer, and the CVs of the mounted sprayer were 92.52% and 94.90%, respectively. The canopy segmentation method could effectively be used to calculate the deposition rate and drioplet distribution in orchard application, while a great deal of time was consumed by counting the number of leaves in the different areas of the fruit tree canopies. Therefore, research on the density of branches and leaves in fruit tree canopies should be carried out in order to improve the efficiency of fruit tree canopy information extraction.

The cutting device in the seedling grafting process was studied, which provided a reference for optimizing the structural parameters and working parameters of important shearing components in the seedling grafting line, thereby improving the performance of the cutting device. The dynamic cutting process of the cutting device was numerically simulated. The effects of four factors, the average cutting speed (X₁), the sliding angle (X₂), the cutting edge angle (X₃), and the cutter clearance (X₄) on the cutting force, were studied. The optimal combination of structural parameters and working parameters of the cutting device was determined. The simulation results showed that the sliding angle (X₂) and the cutting edge angle (X₃) affect the ultimate cutting stress. The average cutting speed (X₁) and the cutter clearance (X₄) affect the ultimate cutting force. When X₁, X₂, X_3, and X₄ are 579 mm/s, 39°, 25°, and 1.4 mm, respectively, it is the better combination parameter, and the ultimate cutting equivalent stress of the cutting device is 0.32 Mpa. A high-speed cutting device for grafted seedlings was built, and the cutting experiment was carried out. The experiment results showed that the simulated values fit well with the experimental data. Under the optimal combination of cutting parameters, the cutting stress of the cutting device was smaller. The finite element simulation of the seedling grafting cutting device reduces the experiment cost and provides a reference for developing the seedling grafting line.

To reduce the cutting force and cutting power consumption during harvest, the cutting mechanical properties of the root of little cabbage were studied. The cutting experiment was carried out using a texture analyzer, and the influence of the individual factors, the cutting bevel angle, the sliding angle, and the cutting gap on the maximum cutting stress and specific cutting energy were studied, respectively. On the basis of single factor experiments, multi-factor experiments were carried out using the central composite design scheme of the response surface method (RSM), and finally, the cutting parameters were optimized. The single factor test results showed that the maximum cutting stress and specific cutting energy first decreased and then increased with the increase in the cutting bevel angle, decreased with the increase in the sliding angle, and first dropped and then went up with the increase in the cutting gap. Response surface test results showed that the order of significance of factors affecting the maximum cutting stress of the root were the oblique angle, sliding angle, and cutting gap in sequence, and the order of the significance of factors affecting the specific cutting energy are cutting gap, oblique angle, and sliding angle. The interaction between the sliding angle and the cutting gap had a significant impact on the maximum cutting stress, and the interaction between the oblique angle and the cutting gap had a significant impact on the cutting energy. The optimal parameter combination is as follows: oblique angle of 9.1°, sliding angle of 30°, and cutting gap of 1.3 mm. At this time, the predicted maximum cutting stress was 7.43 × 104 Pa, and the specific cutting energy was 0.28 mJ mm⁻². Finally, a verification experiment was carried out, and the errors of the predicted and measured values of cutting under the optimal parameter combination were 6.9% and 10.8%, respectively, showing that the cutting parameter optimization results were reliable. This research can provide data support for the design and improvement in the cutting device of the little cabbage combine harvester.

In the last decade, unmanned aerial vehicles (UAVs) for plant protection have rapidly developed worldwide as a new method for pesticide application, especially in China and other Asian countries. To improve the deposition quality in UAV applications, adding appropriate types of spray adjuvants into pesticide solutions is one of the most effective ways to facilitate droplet deposition and control efficacy. At present, research on spray adjuvants for UAVs are mainly based on droplet drift and laboratory tests. Few studies have been conducted on the physicochemical properties of spray adjuvants and the effects of droplet deposition characteristics. To explore the properties of four different kinds of spray adjuvants (Mai Fei, Bei Datong, G-2801, and Agrospred 910) and the deposition characteristics of spray adjuvants on litchi leaves, an automatic surface tension meter, a contact angle measuring device, an ultraviolet visible spectrophotometer, and a DJI AGRAS T30 plant protection UAV was used to measure the surface tension, contact angle, and droplet deposition characteristics on litchi under UAV spraying operations. The results showed that the addition of spray adjuvants could significantly reduce the surface tension of the solution. The surface tension value of the solution after adding the spray additives was reduced by 53.1–68.9% compared with the control solution. Among them, the Agrospred 910 spray adjuvant had the best effect on reducing the surface tension of the solution. The contact angle of the control solution on the litchi leaves varied from 80.15° to 72.76°. With the increase in time, the contact angle of the spray adjuvant solution gradually decreased, the Agrospred 910 spray adjuvant had the best effect, and the contact angle decreased from 40.44° to 20.23° after the droplets fell on the litchi leaves for 60 s. The adjuvant solutions increased the droplet size, but the uniformity of the droplet size decreased. The Dv0.5 of different spray solutions ranged from 97.3 to 117.8 μm, which belonged to the fine or very fine droplets, and the Dv0.5 of adjuvants solutions were significantly greater than that of the control solution. The RSs of adjuvant solutions were very similar and ranged from 0.92 to 0.96, all of which were significantly greater than the result of the control solution (0.57). Compared with the deposition of the control solution, the Mai Fei, Bei Datong, and G-2801 solutions clearly increased spray deposition, with total depositions of 0.776, 0.705, and 0.721 μL/cm², which are all greater than the total deposition of the control solution of 0.645 μL/cm². The addition of tank-mixed adjuvants could effectively increase the uniformity of the spray deposition, and all the average CVs of adjuvant solutions were lower than 96.86%. On the whole, Mai Fei performed best in increasing the spray deposition and promoting penetration, followed by Bei Datong and G-2801. Meanwhile, the test can also provide a reference for improving the utilization rate of UAV pesticide applications.