In this communication, a high-gain partially reflecting surface (PRS) antenna with both in-band and out-of-band radar cross section (RCS) reduction (RCSR) is presented. A microstrip patch antenna acts as the source and is surrounded by the metamaterial ground plane (MGP), which is to reduce the in-band RCS of the proposed antenna. A PRS is located approximately one-half of the wavelength above the MGP to enhance the antenna directivity. In addition, an absorbing surface is adopted to reduce the out-of-band RCS. The design procedure of the antenna is illustrated, and the simulated results reveal that a significant RCSR has been accomplished in the frequency ranges of 8-17 GHz. Compared with the reference antenna, the average out-of-band RCSR is about 13 dB for both TE and TM polarization incident waves. What is more, the in-band RCSR is about 17 dB for the TM polarization incident wave. The simulated results match the measured results well, and the peak gain of the proposed antenna is 18.4 dBi at the operating frequency of 10 GHz.
The method of using millimeter-wave radar sensors to detect human vital signs, namely respiration and heart rate, has received widespread attention in non-contact monitoring. These sensors are compact, lightweight, and able to sense and detect various scenarios. However, it still faces serious problems of noisy interference in hardware, which leads to a low signal-to-noise ratio (SNR). We used a frequency-modulated continuous wave (FMCW) radar sensor operating at 77 GHz in an office environment to extract the respiration and heart rate of a person accustomed to sitting in a chair. Indeed, the proposed signal processing includes novel impulse denoising operations and the spectral estimation decision method, which are unique in terms of noise reduction and accuracy improvement. In addition, the proposed method provides high-quality, repeatable respiration and heart rates with relative errors of 1.33% and 1.96% on average compared with the reference values measured by a reliable smart bracelet.
11 January 2022 in IEEE Transactions on Antennas and Propagation
This article introduces an amplitude and phase independently adjustable transmitarray aperture with a thin profile and low cost to fabrication characteristics, and a transmitarray antenna (TA) featuring the high gain and low sidelobe level (SLL) is realized based on it. The TA is made up of a standard feed horn and a transmitarray aperture, each of which comprises a three-layer metasurface that is well-designed to tune the transmitted phase and amplitude on its own. As a result, the transmitarray aperture can cover the 360° phase range required for phase compensation while also realizing the amplitude distribution calculated by the Taylor design, contributing to the low SLLs. The advantage of independently controlling the amplitude and phase not only enables the proposed TA to be easy to realize and less cost on optimization but also improves the performance of high gain and low SLLs with a low profile and easy fabrication. Theoretical analyses and simulations are carried out, and a prototype is fabricated and measured. At 10 GHz, the measured peak gain is 21.16 dBi, with SLLs of −31.21 and −29.93 dB in the H- and E-planes, respectively. As a result, the tight agreements between measurement and simulation validate the design concept.
19 July 2018 in IEEE Antennas and Wireless Propagation Letters
This letter presents a 3D-printed low-profile end-fire dielectric antenna with wideband performance. The proposed device comprises four dielectric sections that are designed with tapered permittivities and sizes to achieve impedance-matched surface-wave launching over a wide bandwidth. The effective permittivity of dielectric blocks is precisely controlled within the range of 2.0 to 8.3 through varying the infill factor of the 3D printing process. The relation between permittivity and infill factor has been experimentally validated and compared against Bruggeman effective medium approximation theory. Experimental results show that the proposed antenna exhibits a wide impedance bandwidth of 57.7% from 6.9 to 12.5 GHz, a low tilt angle of around 20 degrees over the end-fire direction and a high realized gain above 10 dBi from 7.2 to 12.5 GHz. All these findings demonstrate that 3D printing technology can be leveraged to conveniently fabricate sophisticated antennas with controllable material properties.
9 January 2020 in IEEE Transactions on Antennas and Propagation
A design of dual-band beam-scanning antenna using rotatable planar transmit arrays is proposed in this communication. The antenna is composed of a dual-band lens and a pair of linear phase gradient (PG) transmit arrays (TAs). The presented anisotropic lens is polarization-independent that operating at two frequency bands. The PG TA is implemented by using double square loop units with different phase gradients at two frequencies. Two rotatable PG TAs are located above and parallel to the dual-band lens, and beam scanning in the upper hemisphere is achieved by rotating the two PG TAs synchronously around the axis orthogonal to the planes of the PG TAs. The procedure is demonstrated for dual-band beam scanning implementation operating in linear polarization at X- and Ku-band. The full-wave simulation results demonstrate that the designed antenna enables beam steering in both azimuth and elevation planes at 8 GHz and 14 GHz, with a peak gain of 16.7 dB and 19.8 dB in the broadside direction, respectively. Moreover, a prototype is fabricated, and the measured results confirm the feasibility of using this method for achieving low-cost lightweight, simple configuration dual-band 3-D coverage beam scanning antenna.
1 August 2016 in IET Microwaves, Antennas & Propagation
In this study, the authors present a geometrically symmetrical fractal structure called circular fractal structure. The iterative process of the geometric construction is illustrated and the dimension of the proposed circular fractal structure is 1.5729 based on the similarity dimension. Then, a polarisation insensitive multiband perfect metamaterial absorber (MMA) is proposed based on the circular fractal structure. The proposed MMA has three near‐perfect absorption bands for both transverse electric (TE) and transverse magnetic (TM) polarisations based on the theory of the fractal geometry. The current distribution on the top and bottom surfaces of the MMA are presented to preferably understand the physical mechanism behind the multiband absorption. The simulated results match the experimental results well. For both TE and TM polarisations, the three absorption frequencies are f1 = 2.29 GHz, f2 = 4.28 GHz, and f3 = 11.71 GHz, with the absorptivity of 98.7, 99.4, and 99.5%. Both experimental and simulated results indicate that the proposed circular fractal MMA is a promising candidate for absorbing elements in scientific and military applications.