Yunan Liu

Prof. Dr. Yunan Liu

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in Advanced Composites Letters
Verified
Journal Article
Open access
PDF file
YLYunan Liu
Yunan Liu
SHShutao Huang
Shutao Huang
KJKeru Jiao
Keru Jiao
LXLifu Xu
Lifu Xu
Thin-walled workpieces of silicon carbide particle-reinforced aluminum matrix (SiC p /Al) composites with outstanding properties have been widely applied in many fields, such as automobile, weapons, and aerospace. However, the thin-walled workpieces exhibit poor rigidity, large yield ratio, and easily deform under the cutting force and cutting heat during the machining process. Herein, in order to improve the processing efficiency and precision of higher volume fraction SiC p /Al composite thin-walled workpieces, the influence of different high-speed milling parameters and machining paths on the edge defects is analyzed. The results reveal that the cutting force initially increased and then decreased with the cutting speed. Besides, the cutting force steadily increased with radial cutting depth and feed per tooth, but the influence of feed per tooth is less than radial cutting depth. After up-milling cut-in and cut-out processing and down-milling cut-out processing, the cut-in end of the workpiece exhibited higher breakage and obvious edge defects. However, the workpiece edges remained intact after down-milling cut-in processing. In conclusion, a higher cutting speed, a smaller radial cutting depth, and moderate feed per tooth are required to decrease the cutting force during the milling of SiC p /Al composite thin-walled workpiece. Furthermore, down-milling cut-in processing mode can reduce the edge defects and improve the processing efficiency and precision of the workpiece.

13 January 2025 in Electrical Materials and Applications
Verified
Journal Article
Open access
JLJiajun Luo
Jiajun Luo
WXWeimin Xiao
Weimin Xiao
XLXianhui Li
Xianhui Li
YLYunan Liu
Yunan Liu
The reliable operation of the electric reactor is critical for ensuring energy transmission in the power system. Vibration is an important influencing factor. This study focused on the vibration response characteristics of the electric reactor during the operation process. The vibration at the measuring points on four side surfaces and the top of the oil tank is measured and analysed by applying the rated voltage at the rated frequency on the reactor. The frequency corresponding to the maximum vibration amplitude at the measuring point between the reinforced iron on the side surface of the reactor is determined. The tuned mass damper (TMD) is designed and the material is prepared. The specific frequency tuning mechanism is designed to suppress the reactor's vibration. The damper's optimal structural size is determined based on finite element method according to modal analysis results. According to the simulation results, the designed TMD can provide an inertia force at the target frequency for the controlled structure along the opposite direction, significantly reducing the electric reactor's vibration amplitude and effectively suppressing the vibration at a single frequency. In addition, static analysis and model strength checks are also conducted to ensure the damper's stability and safety in actual applications.

1 January 2020 in Advanced Composites Letters
Verified
Journal Article
Open access
PDF file
XHXu Han
Xu Han
YLYunan Liu
Yunan Liu
LWLihua Wang
Lihua Wang
The physical meaning of phase difference controls the occurrence time of peak values of triangular series, which can be abbreviated as peak arrival time. This article describes a method for deducing the correspondence between the energy distribution characteristics in the time domain and the peak arrival time. The variation laws of acceleration time–history curve of natural seismic wave can be transformed into its energy distribution characteristics in time domain. Based on the needs of seismic engineering, this article proposes a conversion formula to describe the relationship between the peak arrival time and the energy distribution characteristics in the time domain. To ensure that the variation laws of acceleration time–history curve of artificial seismic waves are more consistent with those of natural seismic waves, a normal-fitting annealing algorithm is proposed based on the normal-fitting method. The proposed method not only considers the frequency distribution characteristics of the peak arrival time comprehensively but also optimizes the fitting parameters according to the actual situation. The results of all the experimental cases verify the rationality and reliability of the proposed method.

26 May 2023
Verified
Conference Paper
Closed access
YYYang Yang
Yang Yang
XGXiangsheng Gao
Xiangsheng Gao
YLYunan Liu
Yunan Liu
WXWeimin Xiao
Weimin Xiao
The efficiency of computer numerical control (CNC) machine tools is directly associated with the machine’s ball screw feed system (BSFS). The electromechanical coupling effect of the mechanical structure and the servo system affects the system’s performance. The present study reported a mathematical model for explaining the electromechanical coupling effect by mathematically associating the servo system and the mechanical structure using MATLAB/Simulink. By adding a sinusoidal signal as an input signal in MATLAB/Simulink, the acceleration signals of BSFS were obtained by adjusting the frequency of the input signal. The electromechanical coupling model is verified by simulation and experiments. The simulation results showed that the frequency and amplitude are directly related. No significant difference was noticed between the generated “peak” frequency and the input signal frequency. It is shown that the errors between experimental results and theoretical ones are 16.8% and 2%, respectively, which is acceptable and verifies this established electromechanical coupling model.

12 August 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YTYi Tian
Yi Tian
DHDing-yong He
Ding-yong He
JNJingkai Nie
Jingkai Nie
HQHe Qiang
He Qiang
YLYunan Liu
Yunan Liu
Aluminium alloy honeycomb vibration isolators, owing to their thin-walled nature and periodic structure, offer numerous advantages, including lightweight construction, high strength, structural stability and simplicity of design parameters. Traditional honeycomb structures exhibit high stiffness in the coplanar direction but offer virtually no vibration isolation. To develop the vibration isolation performance of honeycomb structures in the coplanar direction and achieve vibration isolation protection for precision electronic instrument cabinets, this paper introduces a periodic corrugated structure based on traditional straight-hole honeycombs, designs a new type of corrugated honeycomb isolator, and screens and refines its vibration isolation performance. Using finite element simulation, multiple sets of orthogonal experiments were designed to perform range analysis on the simulation results, gradually eliminating the interference of irrelevant factors on the vibration transmission rate and optimising the dimensional parameters of the corrugated honeycomb isolator. To further optimise the vibration isolation performance of the corrugated honeycomb isolator, periodic circular holes were opened in the X and Y directions of the isolator, reducing its vibration transmission rate in the Z-direction and effectively improving the vibration isolation effect. Simultaneously, sweep frequency tests were designed to verify the accuracy of the finite element model.

1 August 2021 in INTER-NOISE and NOISE-CON Congress and Conference Proceedings
Verified
Journal Article
Closed access
JZJunjuan Zhao
Junjuan Zhao
LZLiying Zhu
Liying Zhu
XLXinyun Li
Xinyun Li
YWYueyue Wang
Yueyue Wang
WWWenjiang Wang
Wenjiang Wang
YLYunan Liu
Yunan Liu
To achieve a compact design for low frequency tunable sound absorption, a membrane sound absorber (MSA) with nonlinear magnetic field is proposed in this paper. By employing a central iron platelet on the membrane, the MSA can be easily tuned by introducing a magnet at a distance from the platelet that can be adjusted. To investigate the low frequency properties of MSA with different magnets and iron-platelets, a series of impedance tube experiments are conducted in detail. The sample absorber has a rear cavity depth of 30 mm, three different magnets were used inside, tested results real that using a strong magnetic field can help broaden the frequency tuning range. Then, results from the MSA with five different sizes of iron plates tuned by one magnet show that the low-frequency tuning range moves to lower with the increase of the area of iron plates.