Kamel HEBBACHE

Dr. Kamel HEBBACHE

Civil engineering, University Ferhat Abbas of Setif, Sétif, Algeria
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
RBRiad Babba
Riad Babba
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
MBMourad Boutlikht
Mourad Boutlikht
RHRedha Hammouche
Redha Hammouche
Laura MorettiLaura Moretti
Laura Moretti
Premature debonding between carbon fiber-reinforced polymer (CFRP) and concrete is a critical issue in structural reinforcement applications, often leading to a significant reduction in the load-carrying capacity of the system. This failure mode is typically initiated by inadequate adhesion at the interface, compromising the effectiveness of CFRP in enhancing the structural performance of concrete elements. To address these issues, this study explores the impact of silica sand on the mechanical and adhesion properties of epoxy resin composites. Initially, this paper investigates the physical and mechanical properties of epoxy resin composites by varying the ratios of silica sand from 0% to 15% by volume. Subsequently, it examines the effectiveness of these composites as sealing materials to enhance the bond strength between CFRP and concrete. Incorporating a 10% silica content improves the mechanical properties of the epoxy resin, with the tensile strength increasing from 29.47 MPa to 35.52 MPa and an elastic modulus from 4.38 GPa to 5.83 GPa. Furthermore, silica sand enhances the adhesion strength between CFRP and concrete, as confirmed by the increase in the pull-out force from 14.21 kN to 18.79 kN. Silica particles improve surface roughness and interlocking, contributing to a better load distribution and stress transfer at the interface. Therefore, silica-filled epoxy resin is an efficient material for CFRP–concrete bonding applications.

25 October 2023 in Materials
Verified
Journal Article
Open access
PDF file
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
MBMourad Boutlikht
Mourad Boutlikht
STSeifeddine TABCHOUCHE
Seifeddine TABCHOUCHE
CBCherif Belebchouche
Cherif Belebchouche
Laura MorettiLaura Moretti
Laura Moretti
The environmental impacts of cement manufacturing are becoming a real-time issue that requires attention. This paper investigates the mechanical and physical properties of mortars with finely ground sand as a substitute for cement. The experimental program consisted of three silica sands with a Blaine Specific Surface (BSS) area of 459 m2/kg, 497 m2/kg, and 543 m2/kg and four substitution ratios of 10%, 20%, 30%, and 40%. A total of 12 mixtures have been prepared and tested for comparison to the reference mortar. The pozzolanic effect of the sand was evaluated using thermogravimetric analysis (TGA). The results revealed that the fineness variation from 459 m2/kg to 543 m2/kg resulted in an increase of 20% and 30% in water absorption and compressive strength, respectively. However, increasing the substitution ratio from 10% to 40% led to a 40% decrease in mechanical strength and a 25% increase in water absorption. The statistical analysis of the results demonstrated that both factors under study influenced compressive strength and water absorption. The ANalysis of VAriance (ANOVA) confirmed that the proposed regression equations predict the experimental results. Further studies will investigate both the technical and environmental performances of cement mortars with finely ground silica sand.

9 January 2023 in NRIAG Journal of Astronomy and Geophysics
Verified
Journal Article
Open access
ACAmmar Chibani
Ammar Chibani
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
MMMekki Mellas
Mekki Mellas
AMAbdelhak Mabrouki
Abdelhak Mabrouki
Constantine is city characterised by a very rugged relief in which frequently happened the collapse of buildings as a result of landslide hazards. The aims of this study are to determine the depth of the surface landslide and to evaluate the landslide mass in the new city of Ali Mendjeli, which is nearby Constantine in Northeastern Algeria, using a geophysical method, namely the electrical resistivity tomography (ERT). Five two-dimensional (2D) ERT profiles were performed along and across the landslide using Wenner electrode array. Two parallel profiles to the sliding direction of 69 m length of each profile and three other perpendicular profiles, each with a length of 115 m, were conducted with inter-electrode spacing of 3 and 5 m, respectively. The resistivity data processing was carried out using Res2Dinv software. The inverted pseudo-section models presented formations characterised by low resistivities which can be summarised in two sets ranging from 1.38 to 6.20 Ωm and from 6.20 to 19 Ωm. The inverted resistivity data were correlated and calibrated with respect to the subsoil lithology obtained by well drilling and inclinometer tests. According to the inclinometer displacements, the measurements were of the order of 2–3 mm for a depth of 10 m and between 17.5 and 19.5 m for a depth of 13 m. The combined measurements of ERT and the geotechnical testing not only have shown a good agreement in the results obtained but also have successfully detected the depth of probable rupture surfaces and displaced materials likely to slip. This concordance of the obtained results. The estimated volume of the sliding material was around 20.000 m3. According to the obtained results of this study, ERT can be applied to detect sliding surfaces in landslides.

4 January 2025 in Construction and Building Materials
Verified
Journal Article
Closed access
NKNour El Houda Khitas
Nour El Houda Khitas
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
ADAbdellah Douadi
Abdellah Douadi
MBMourad Boutlikht
Mourad Boutlikht
CBCherif Belebchouche
Cherif Belebchouche
Marijana Hadzima-NyarkoMarijana Hadzima-Nyarko
Marijana Hadzima-Nyarko

19 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
AKAbdelhamid Karouche
Abdelhamid Karouche
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
CBCherif Belebchouche
Cherif Belebchouche
NLNoureddine Lahbari
Noureddine Lahbari
OKOussama Kessal
Oussama Kessal
Sławomir CzarneckiSławomir Czarnecki
Sławomir Czarnecki
Carbon-fiber-reinforced polymer (CFRP) is a composite material used to mend and strengthen concrete structural elements in civil engineering. The prime aim of this experimental study is to investigate the comportment of confined concrete cylinders (CCC) under uniaxial loads by altering the concrete strength, the CFRP angle orientation, and the volumetric ratio, following the externally bonded reinforcement technique (EBR). We present the results of the confinement effect and failure mechanisms issue of more than 150 specimens of CFRP confined concrete cylinders that have been undertaken and in which several parameters were altered. Totally and partially confined concrete cylinders were tested for failure under axial compressive loads and indirect tensile tests. Four different ratios of water/cement (0.33, 0.36, 0.401, and 0.522) were investigated. In addition, three sand–resin ratios were prepared to improve the mechanical properties and the adhesion of the CFRP and the concrete. The obtained results revealed a clear improvement in the compressive strength of the specimens made with low strength concrete (from 38% to 66%) compared to those made of high strength concrete (from 11% to 31%), where the improvements are relatively low. Furthermore, the transversally confined concrete cylinders presented significant gains in strength over those confined longitudinally. Lastly, adding sand to the resin increases the compressive strength of confined concrete cylinders (1.19% to 54.62%) and reduces the cost of the resin used for fixing CFRP materials.

24 March 2025 in Buildings
Verified
Journal Article
Open access
PDF file
MBMourad Boutlikht
Mourad Boutlikht
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
NKNour El Houda KHITAS
Nour El Houda KHITAS
AMAbderraouf MESSAI
Abderraouf MESSAI
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
TTTaher A. Tawfik
Taher A. Tawfik
The disposal and recycling of industrial by-products such as marble and limestone powders pose pressing environmental challenges due to the substantial amounts of waste generated annually by marble processing plants and limestone quarries. The integration of these by-products into concrete production is justified by their widespread availability and the potential to alleviate the environmental burden. This study used a statistical mixture design approach to systematically assess the effects of limestone and marble powders, with varying fineness levels, as partial cement replacements (up to 17%) on the rheological and mechanical properties of self-compacting concrete (SCC). The experimental findings revealed that the density of the SCC mixtures ranged from 2475 to 2487 kg/m3. Mixtures incorporating limestone powder exhibited superior flowability, achieving a slump flow of up to 69 cm, an 8% improvement compared to those containing marble powder. However, marble powder with a specific surface area of 330 m2/kg demonstrated significant improvements in compressive and tensile strengths, with increases of 18%. Statistical analysis using analysis of variance (ANOVA) validated the reliability of the predictive models developed, which demonstrated coefficients of determination (R2) that exceeded 0.94 and p-values below 0.05. These models enable precise predictions of critical performance metrics, including density, slump flow, box flow, compressive strength, and tensile strength, thus reducing the need for extensive experimental procedures.