The combination of multi-phase extension and pre-existing fault reactivation results in a complex fault pattern within hydrocarbon-bearing basins, affecting hydrocarbon exploration at different stages. We used high-resolution 3D seismic data and well data to reveal the impact of multi-phase extension and pre-existing fault reactivation on Cenozoic fault pattern changes over time in the Jiyang Depression of eastern China. The results show that during the Paleocene, a portion of NW-striking pre-existing faults reactivated under NS extension and controlled the basin structure (type 1). Other parts of the NW-striking pre-existing faults stopped activity and served as weak surfaces, and a series of NNE-striking faults were distributed in an en-echelon pattern along the NW direction at shallow depths (type 2). In areas unaffected by pre-existing faults, NE-striking faults formed perpendicular to regional stresses. During the Eocene, the regional stresses shifted clockwise to near-NS extension, and many EW-striking faults developed within the basin. The NE-striking faults and the EW-striking faults were hard-linked, forming the ENE-striking curved faults that controlled the structure in the basin (type 3). The NNE-striking faults were distinctly strike-slip at this time, with the ENE-striking faults forming a horsetail pattern at their tails. Many ENE-striking faults perpendicular to the extension direction were formed in areas where the basement was more stable and pre-existing faults were not developed (type 4). There were also developing NS-striking faults that were small in scale and appeared in positions overlapping different main faults (type 5). Additionally, different fault patterns can guide different phases of hydrocarbon exploration. Type 1, type 2, and type 3 faults are particularly suitable for early-stage exploration. In contrast, type 4 and type 5 faults are more appropriate for mature exploration areas, where they may reveal smaller hydrocarbon reservoirs.
Sedimentary facies identification constitutes a cornerstone of reservoir engineering. Traditional facies interpretation methods, reliant on manual log-response parameter analysis, are constrained by interpreter subjectivity, reservoir heterogeneity, and inefficiencies in resolving thin interbedded sequences and concealed fluvial sand bodies—issues marked by high interpretive ambiguity, prolonged cycles, and elevated costs. This study focuses on the Lower Cretaceous Yaojia Formation Member 1 (K2y1) in the satellite oilfield of the Songliao Basin, integrating sequence stratigraphy into a machine learning framework to propose an innovative convolutional neural network (CNN)-based facies recognition method using log-curve image groups by graphically transforming five log curves and establishing a CNN model that correlates log responses with microfacies. Results demonstrate the model’s capability to identify six microfacies types (e.g., subaqueous distributary channels, estuary bars, sheet sands) with 83% accuracy, significantly surpassing conventional log facies analysis. This breakthrough in interpreting complex heterogeneous reservoir lithofacies establishes a novel technical avenue for intelligent exploration of subtle hydrocarbon reservoirs.
The Silurian system in Tazhong area is characterized by extensive, low-abundance lithological reservoirs with strong diagenesis, resulting in significant heterogeneity. The complex pore structure in this area significantly impacts fluid control, making accurate characterization and classification of pore structures crucial for understanding reservoir properties and their influence on oil and gas distribution. Based on 314 Mercury Injection Capillary Pressure (MICP) samples in combination with core slices and thin casting slices observation, a pipeline of characterization and classification scheme by data-mining analytics of strong diagenesis sandstone pore structure types in the study zone is established, and the characteristics of different pore structures are clarified. According to the pore structure parameter abstracted by MICP data compression and variable analysis based on hierarchical clustering and principal component analysis (PCA) analysis, the variables are reasonably evaluated and screened, and the screened variables can be divided into three groups: mean pore throat radius-maximum pore throat radius-median pore throat radius-pore throat diameter mean variable group, microscopic mean coefficient variable group, and median pressure displacement pressure-relative sorting coefficient variable group. The combination of classification schemes analysed by decision tree model and linear discriminant analysis (LDA) model was determined. In the two-dimensional projection diagram of LDA model, a relatively obvious distribution of low displacement pressure, middle displacement pressure and high displacement pressure was obtained, and three distribution lines were nearly parallel. Based on the relevant information, 6 combined classification schemes suitable for final pore structure modelling were determined verified by microscopic observation. The correct characterization and classification of pore structure can be applied to the prediction of pore type, which can be used to improve the prediction of oil and gas distribution and oil and gas recovery in the future.
The structure of coal bodies is the product of brittle or ductile deformation in coal reservoirs under tectonic stress, serving as a crucial parameter influencing pore distribution characteristics, permeability, adsorption-desorption capacity, and mine safety in coal reservoirs. It holds significant research importance for the exploration and development of coal resources and coalbed methane (CBM). Under stratigraphic temperature and pressure conditions, the chemical structure and physical properties of coal reservoirs undergo corresponding deformation and evolution, leading to changes in the stress field surrounding the coal reservoir, as well as alterations in coal rock strength, pore characteristics, adsorption-desorption capacity, and permeability. Seismic data encompasses various attributes such as amplitude, frequency, and phase, with distinct differences in rock physics attributes among different coal body structures, which are closely related to seismic attributes. Through multi-attribute analysis, seismic attributes associated with coal body structures can be extracted. Machine learning is capable of processing and interpreting the nonlinear relationships between vast amounts of seismic data and rock physics attributes. By establishing a coal body structure prediction model based on machine learning technology, the accuracy of coal body structure predictions can be enhanced, allowing for an understanding of the distribution characteristics of tectonic coal in the study area and providing a reference for CBM (methane) extraction, thereby effectively improving the efficiency of CBM (methane) mining.
Tectonic deformation can substantially change the pore characteristics and the resulting methane adsorption capacity of shales; thus, it strongly influences shale gas exploration and development in structurally complex areas of southern China. Two sets of shales with identical lithofacies that were derived from either structurally stable or deformed regions were collected at Fuling Field to evaluate the response of their pore properties and methane adsorption behavior to tectonic deformation through field emission scanning electron microscopy (FE-SEM), low-pressure gas (CO2/N2) adsorption, and high-pressure methane adsorption experiments. Three primary shale lithofacies were identified in each set of shales: organic-lean (OL) siliceous-rich argillaceous (CM-1) shale lithofacies, organic-moderate (OM) argillaceous/siliceous mixed (M-2) shale lithofacies, and organic-rich (OR) argillaceous-rich siliceous (S-3) shale lithofacies. In the stable region, organic matter (OM) pores dominated the pore types of OR S-3 shales, whereas the primary pore types of OL CM-1 shales were clay cleavage micro-fractures. OM M-2 shales exhibited a composite type of OM pores and clay cleavage micro-fractures. Compared with structurally stable shales, the original OM-hosted and clay-related pores in structurally deformed shales were extensively compacted or even closed due to tectonic compression during structural deformation. Despite pore collapse, two new types of tectonic micro-fractures were generated and found to be well developed in deformed shales through the rupture of brittle minerals in OR S-3 shales and the deformation of clay minerals in OL CM-1 shales. Simultaneously, organic matter–clay aggregates that formed during tectonic compression constituted a distinctive structure in deformed OM M-2 shales. As a result, the deformed shales displayed a decrease in their micropore and mesopore volumes, as well as a decrease in their pore surface areas, because of strong tectonic compression accompanied by an increase in the macropore volume due to the development of tectonic micro-fractures. Furthermore, the large pore surface areas in structurally stable shales could supply abundant adsorption sites and facilitate the enrichment of adsorbed gas. The expanded macropore volumes in structurally deformed shales could provide more storage spaces that are favorable for the accumulation of free gas.