Aquathermolysis is one of the crucial processes being considered to successfully upgrade and irreversibly reduce the high viscosity of heavy crude oil during steam enhanced oil recovery technologies. The aquathermolysis of heavy oil can be promoted by transition metal-based catalysts. In this study, the catalytic performance of two water-soluble catalysts Ni(CH₃COO)₂ and Zn(CH₃COO)₂ on the aquathermolytic upgrading of heavy oil at 300 °C for 24 h was investigated in a high pressure–high temperature (HP-HT) batch reactor. The comparison study showed that nickel acetate is more effective than zinc acetate in terms of viscosity reduction at 20 °C (58% versus 48%). The viscosity alteration can be mainly explained by the changes in the group composition, where the content of resins and asphaltenes in the upgraded heavy crude oil sample in the presence of nickel catalyst was reduced by 44% and 13%, respectively. Moreover, the nickel acetate-assisted aquathermolysis of heavy oil contributed to the increase in the yield of gasoline and diesel oil fractions by 33% and 29%, respectively. The activity of the compared metal acetates in hydrogenation of the crude oil was judged by the results of the atomic H/C ratio. The atomic H/C ratio of crude oil upgraded in the presence of Ni(CH₃COO)₂ was significantly increased from 1.52 to 2.02. In addition, the catalyst contributed to the desulfurization of crude oil, reducing the content of sulfur in crude oil from 5.55 wt% to 4.51 wt% The destructive hydrogenation of resins and asphaltenes was supported by the results of gas chromatography-mass spectroscopy (GC-MS) and Fourier-transform infrared (FT-IR) spectroscopy analysis methods. The obtained experimental results showed that using water-soluble catalysts is effective in promoting the aquathermolytic reactions of heavy oil and has a great potential for industrial-scale applications.

In this study, for the first time we investigated the in situ upgrading performance of Na metal nanoparticles, which were obtained by dispersing small pieces of sodium in liquid paraffin up to certain dispersity. In situ aquathermolytic reactions were modeled in a high pressure–high temperature reactor coupled with a Gas Chromatography (GC) system at a temperature of 250 °C for 24 h using a heavy oil sample, produced from the Ashal’cha reservoir, Republic of Tatarstan (Russia). The mean particle size of Na nanoparticles was 6.5 nm determined by the Dynamic Light Scattering (DLS) method. The nanoparticles were introduced to the reaction medium with a concentration of 2 wt.% The upgrading performance of Na nanoparticles was evaluated by several analytical methods such as Gas Chromatography (GC), elemental analysis (CHNS), SARA, Gas Chromatography–Mass Spectroscopy (GC-MS), FT-IR spectroscopy and viscosity measurements. It was revealed that Na nanoparticles interact with water to yield hydrogen gas, the concentration of which increases from 0.015 to 0.805 wt.% Moreover, the viscosity of upgraded heavy oil was reduced by more than 50% and the content of low-molecular-weight hydrocarbons in saturated and aromatics fractions was increased. The Na nanoparticles contributed to the utilization of hydrogen sulfide and carbon dioxide by 99 and 94 wt.%, respectively.

An attempt to combine two ‘green’ compounds in nanocomposite microcontainers in order to increase protection properties of waterborne acryl-styrene copolymer (ASC) coatings has been made. N -lauroylsarcosine (NLS) served as a corrosion inhibitor, and linseed oil (LO) as a carrier-forming component. LO is compatible with this copolymer and can impart to the coating self-healing properties. For the evaluation of the protective performance, three types of coatings were compared. In the first two, NLS was introduced in the coating formulation in the forms of free powder and micro-containers filled with LO, correspondingly. The last one was a standard ASC coating without inhibitor at all. Low-carbon steel substrates were coated by these formulations by spraying and subjected subsequently to the neutral salt spray test according to DIN ISO 9227. Results of these tests as well as the data obtained by electrochemical study suggest that such containers can be used for the improvement of adhesion of ASC-based coatings to the substrate and for the enhancement of their protective performance upon integrity damage, whereas the barrier properties of intact coatings were decreased.