Purpose: The purpose of this paper is to reveal the transient thermo-elasto-hydrodynamic lubrication mechanism of a bidirectional thrust bearing in a pumped-storage unit, and to propose the transient simulation method of two-way fluid-solid-thermal interaction of thrust bearing.Design/methodology/approach: The transient fluid-solid-thermal interaction method is used to simulate the three-dimensional lubrication of the thrust bearing, during the start-up and shutdown process of a pumped storage unit. A pad including an oil hole is modelled to analyze the temporal variation of lubrication characteristics, such as the film pressure, thickness and temperature, during the transient operation process.Findings: The injection of the high-pressure oil sufficiently affects the lubrication characteristics on film, in which the hysteresis phenomena were found between the start-up and shutdown possess.Originality/value: This paper reveals the transient lubrication mechanism of tilting pad in a thrust bearing, by means of transient fluid-solid-thermal interaction method. Lubrication characteristics are simulated without assuming the temperature relationship between the oil film inlet and the outlet and the heat transfer on the pad free surface. This paper provides a theoretical basis for the safe design and stable operation of thrust bearings.
10 May 2022 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
Pump-turbine plays a significant role in the pumped storage station, and it is troubled by unreasonable hydraulic thrust. Some pressure balance devices have been adopted to ensure the safety of the pump-turbine unit, but the effect mechanism has not been numerical studied. This paper establishes the CFD model of the flow passage of a pump-turbine, wherein the crown gap, band gap, pressure balance pipe, and the discharge ostium are considered. Then, the flow characteristics of the pump-turbine at four typical operating conditions in turbine mode are calculated in transient scheme, and the numerical results agree with the experimental results. Finally, the effect of the pressure balance pipe and the discharge ostium on the pressure pulsation and the hydraulic thrust is discussed. The results show that the pressure balance pipe causes the direction of the axial hydraulic thrust to change from downward to upward, and the discharge ostium helps reducing the axial hydraulic thrust to a reasonable range. The pressure balance pipe and the discharge ostium have little effect on the radial hydraulic thrust. The pressure pulsation analysis provides a basis for revealing the mechanism of the hydraulic thrust frequency, and the rotor-stator interaction frequency exists in the axial hydraulic thrust. This paper provides a deeper knowledge of the impact mechanism of the pressure balance pipe and discharge ostium on the flow characteristics of the pump-turbine, which could contribute to future designs of the pump-turbine units, and is helpful for improving the safety of the pumped storage unit.
The free-surface vortex is simulated with the homogeneous mixture approach. In order to define suitable boundary conditions in the two-phase flow field, a numerical strategy is proposed on the air mass conservation in a recirculating flow system. The numerical approach is verified from an experiment. Numerical results agreed well with the experiment not only in the vortex circulation but also in the axial velocity gradient. On the homogeneous mixture assumption, the compressibility corrections for the turbulence modelling had almost no effect on the result in this case study. In order to estimate the continuous air–core length, the visible air–core interface was assumed to be characterized by the constant void fraction. With validated numerical results, vortex air core was visualized by the air volume fraction, based on the air–core length in not only the experiment but also the analytical model in the applicable range.
The S-shaped characteristic curves in pump-turbines complicate synchronization with the electrical grid and affect system safety. Misaligned guide vanes (MGVs) are one of the most effective solutions to avoid S-shaped characteristics. The internal flow mechanism with the MGV for improving S-shaped characteristics was studied by numerical analysis. Six operating conditions were modeled in the S-shaped region. Four guide vanes were arranged as the MGVs to qualitatively and quantitatively analyze the flow behavior. The internal flow was quite complex at the four operating points without the MGV; here, the attack angle and the flow behavior had no obvious difference at each vane. For the similar conditions with MGVs, attack angles and internal flow fields varied clearly at each vane, especially in the vaneless region and in the runner blade passages. For the same discharge rates, total openings, and rotating speeds, the internal flows were quite different between with and without the MGVs. The MGVs disrupt the high-speed circumferential water ring (appreciably faster compared to the main flow) in the vaneless region and maintain operation with higher unit speeds. Consequently, the unit speed is larger at the same unit discharge in the S-shaped region. Therefore, the MGV method can reduce S-shaped characteristics.
22 July 2021 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
Blade leaning is commonly seen in the runner design of reversible pump turbines which operate under varying conditions. However, there is no certain law in determine the leaning mode and level. Considering performance, hydraulic excitation and structural response, five runners with strong rotational (RL+), rotational (RL), strong counter-rotational (CL+), counter-rotational (CL) and without (NL) blade leaning are compared under high-efficiency condition in pump mode and turbine mode. The head, efficiency, internal flow pressure pulsation and runner stress are comparatively studied. Among the five runners, CL+ runner is found has the highest efficiency as pump when RL+ runner has the highest efficiency as turbine. Pressure pulsation results show that the rotor-stator interaction region is the strongest pulsation source especially for runner and blade frequencies. In pump mode, pressure pulsation intensity decreases when blade leaning mode gradually changes from rotational to counter-rotational. In turbine mode, the NL runner has the strongest pressure pulsation intensity in runner and guide vane. Both rotational and counter-rotational leaning will reduce pressure pulsation. Velocity contours indicate that blade leaning will affect the velocity uniformity especially along rotational direction and cause stronger or weaker local hydraulic excitation. Under hydraulic excitation, RL+ runner suffers the highest equivalent stress as pump while CL runner suffers the highest equivalent stress as turbine. From rotational to counter-rotational blade leaning, the maximum stress moves on the crown from low pressure side to high pressure side. Considering hydraulic excitation and structural response, the strong counter-rotational leaning blade is found better in reversible runner design.
Purpose: The purpose of this paper is to study the pressure fluctuation characteristics in the sidewall gaps of a centrifugal dredging pump in detail and discover the excitation sources. Design/methodology/approach: An unsteady numerical simulation with shear–stress transport–scale-adaptive simulation (SAS-SST) model was conducted for a centrifugal pump considering the sidewall gaps. The numerical codes were validated by a model test carried out in China Water Resources Beifang Investigation, Design and Research Co., Ltd. Fast Fourier transform was used to obtain the frequency components of the pressure fluctuation. Findings: Pressure fluctuation characteristics inside the pump were analyzed for a condition near the design point. In the sidewall gaps, the circumferential, radial and axial distribution of the pressure fluctuation amplitude follow different laws. The non-axisymmetrical distribution of pressure fluctuation in the sidewall gaps shows that the unsteady flow in the volute casing which has a non-axisymmetrical geometry imposes an evident effect on the flow field in the sidewall gaps and the interaction between the main flow and the clearance flow cannot be neglected. There are several frequency components appearing as the dominant frequencies at different locations in the sidewall gaps, but the relatively stronger pressure fluctuations are all dominated by the rotating frequency. It indicates that the rotating impeller, which originally makes the shrouds rotate, is the primarily excitation source of the pressure fluctuations in the sidewall gaps. Originality/value: The pressure fluctuation characteristics in the sidewall gaps of centrifugal pumps were first comprehensively analyzed. Unsteady flows in the sidewall gaps should be considered during the design and operation of centrifugal pumps.