Graphene and silica are two materials that have wide uses and applications because of their unique properties. Graphene/silica hybrid composite, which is a combination of the two, has the good properties of a combination of graphene and silica while reducing the detrimental properties of both, so that it has promising future prospects in various fields. It is very important to design a synthesis method for graphene/silica composite hybrid materials to adapt to its practical application. In this review, the synthesis strategies of graphene, silica, and hybrid graphene/silica composites such as hydrothermal, sol-gel, hydrolysis, and encapsulation methods along with their results are studied. The application of this composite is also discussed, which includes applications such as adsorbents, energy storage, biomedical fields, and catalysts. Furthermore, future research challenges and futures need to be developed so that hybrid graphene/silica composites can be obtained with promising new application prospects.
We reported in this study the interrelation between the addition of 0.4, 0.8, 1.2, and 1.6 wt. % reduced graphene oxide (r-GO) into PVA/Alginate and their degradation and biocompatibility properties. The r-GO was synthesized by using the Hummer’s method. A crosslinker CaSO4 was added to prepare Alginate/PVA/r-GO Hydrogel composite. A Field Emission in Lens (FEI)-scanning electron microscopy (SEM), along with X-ray energy dispersive spectroscopy (EDS), was performed, characterizing the morphology of the composite. A compressive test was conducted, determining the mechanical properties of the composite with the highest achieved 0.0571 MPa. Furthermore, in vitro cytotoxicity was conducted to determine the biocompatibility properties of the studied composite. An MTT assay was applied to measure cell viability. In general, the presence of r-GO was found to have no significant effect on the morphology of the hydrogel. Indeed, adding 0.4% r-GO to the PVA/Alginate increased the cell viability up to 122.26 ± 0.93, indicating low toxicity. The studied composites have almost no changes in weight and shape, which proves that low degradation occurred in addition to this after 28 days of immersion in saline phosphate buffer solution. In conclusion, achieving minimal degradation and outstanding biocompatibility lead to PVA/Alginate/r-GO hydrogel composites being the most attractive materials for tissue engineering applications.
1 July 2017 in IOP Conference Series: Materials Science and Engineering
Poly (butylene adipate-co-terephthalate (PBAT) nanocomposites were prepared by melt blending PBAT with 5 wt.% of modified or unmodified montmorillonites (MMT). The effect of the presence of organic modifiers in MMT on the morphological, crystalline, thermal, and mechanical properties of PBAT nanocomposites was evaluated. The dispersion and distribution of the clays were studied by using wide angle X-ray analysis (WAXS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) analysis. Materials characterization techniques included: contact angle measurements, differential scanning calorimetry (DSC), thermogravimetry (TGA) and surface hardness analysis. As general results, nanocomposites exhibited different level of clay dispersion depending on the clay/organic modifier's chemical affinity with the polymer. Contact angle measurements show increases in the hydrophobicity level of PBAT based CLO30B, this could depict its high potential for packaging applications. In addition, Thermal analysis showed that clays partially hindered kinetics and extent of PBAT crystallization on cooling. In general, thermal properties of PBAT were improved by addition of clays, for a barrier effect of the nanoparticle towards polymer decomposition products ablation. In parallel, addition of clays led to enhancements in polymer hardness. These properties were found to be apparently influenced by clay dispersion level and chemical compatibility between the organic modifier and polymer matrix.
31 May 2017 in IOP Conference Series: Materials Science and Engineering
The composite based Zinc-doped in Chitosan/Hydroxyapatite was successfully prepared by wet mixing method through the addition of 10, 15, and 20wt% of chitosan. The addition of Chitosan increased the compressive strength and the modulus elasticity. However, it decreased the density and the surface hardness of HA-Zn. Mechanical characterization revealed that these composites are suitable as a candidate of a cancellous bone substitute. Composite with 10% chitosan has compressive strength and modulus elasticity of 57.03 MPa and 0.15 GPa, respectively. Hence, it has the physical and mechanical properties that meet the standards as a cancellous bone substitute material. Also, in vitro biocompatibility test against BHK-21 cells exhibited non-toxic materials.
Studi Pengaruh Penambahan PVA dan Bentonit Terhadap Morfologi dan Sifat Fisik Komposit Berbasis Hidrogel Alginat Sebagai Kandidat Material Perancah Untuk Regenarasi Tulang Rawan
1 July 2017 in IOP Conference Series: Materials Science and Engineering
Hydroxyapatite (HAp) doping with zinc was prepared using sol gel method; different chitosan content were further added to prepare the composite, namely 10, 15 and 20% wt. The samples were characterized using FTIR, XRD, SEM-EDX, and AAS. In vitro antimicrobial activities of the composite were evaluated against gram positive and negative bacteria. FTIR results revealed that there were no important changes in the structure of composite, while 10% wt of chitosan in composite shows the highest inhibition zone against Escherichia coli after 24 h incubation. In addition, after 7 days of immersion in simulated body fluid, there were apatite formations in the surface of the composite. These might indicate that this composite could be used as a material candidate for bone substitute applications.