M. P. Jenarthanan

Dr. M. P. Jenarthanan


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 November 2019 in Polymer Composites
Verified
Journal Article
Closed access
PDF file
GRGiridharan Rajaraman
Giridharan Rajaraman
SASantosh Kumar Agasti
Santosh Kumar Agasti
MJM. P. Jenarthanan
M. P. Jenarthanan

22 March 2021 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
SRS Ramesh
S Ramesh
MJM. P. Jenarthanan
M. P. Jenarthanan
Powder Mixed Electric Discharge Machining has been the main focus of many researchers for quite a long time. The performance of EDM process has been improved significantly by using powder mixed dielectric medium. Numerous researches were undertaken to study the influence of different process parameters involved in the powder mixed EDM by experimenting with different work materials and powder combination. The objective of this work is to conduct experimental study on the powder Mixed EDM of a Nickel based super alloy, Nimonic 75, using three different powders which are graphite, silicon and manganese. The other important process parameters considered are concentration of powder (Cp), peak current (Ip), duty factor (DC). The experiments were conducted based on the Response Surface Methodology (RSM) design. The important measures of performance of EDM process chosen in this study are Material Removal Rate (MRR), Electrode Wear ratio (EWR) and Surface Roughness (SR). Graphite powder yielded highest MRR and silicon powder produced good finish of the components. The influence of powder at higher concentration is not significantly high. Moreover, Higher duty cycle caused the decrease of MRR, EWR and increase of SR. This works also aims to optimize the process parameters using Grey Relational Analysis (GRA) combined with Fuzzy logic method. The optimum conditions identified based on GFRG was powder = Mn; concentration = 3 g/l; discharge current = 4 A and duty cycle = 0.9 It was also estimated that the error in predicting best output of the PMEDM process is below 6%.

20 December 2013 in Pigment & Resin Technology
Verified
Journal Article
Closed access
MJM. P. Jenarthanan
M. P. Jenarthanan
RJR. Jeyapaul
R. Jeyapaul

26 November 2015 in Australian Journal of Mechanical Engineering
Verified
Journal Article
Closed access
KJK. Jagathesh
K. Jagathesh
MJM. P. Jenarthanan
M. P. Jenarthanan
PBP. Dinesh Babu
P. Dinesh Babu
CCChanakyan Chandrasekaran
Chanakyan Chandrasekaran
Friction Stir Welding (FSW) is a solid state joining technique which is universally used for joining of aluminium alloys in marine, aerospace, automotive and many other applications of commercial importance. In the present study, the effect of FSW parameters on the weldability of dissimilar aluminium alloys called AA2024 and AA6061 was investigated. The two plates were aligned perpendicular to the rolling directions and the welding was carried out. The main objective of the experiment was to find out the maximum tensile strength. The experiments were conducted on a milling machine. Three-factor three levels Box–Behnken matrix in response surface methodology is employed to carry out the experimental investigation. The “Design Expert 8.0” software was used for regression and graphical analyses of data collected. Analysis of variance was used to check the validity of the model. Designed FSW experiments were carried out to get high strength welding by controlling the rotational, welding speed and tool pin diameter. The tensile tests were carried under tension at room temperature in order to analyse the mechanical response.

12 April 2018 in Multidiscipline Modeling in Materials and Structures
Verified
Journal Article
Closed access
RSRamesh S.
Ramesh S.
MJM. P. Jenarthanan
M. P. Jenarthanan
BABhuvanesh Kanna A.S.
Bhuvanesh Kanna A.S.
Purpose: The purpose of this paper is to investigate the performance of powder-mixed electric discharge machining (PMEDM) using three different powders which are aluminium (Al), silicon carbide (SiC) and aluminium oxide (Al2O3). Besides that, the influence of different tool materials was also studied in this experimental investigation. Hence, the work material selected for this purpose was AISI P20 steel and tool materials were copper, brass and tungsten. The performance measures considered in this work were material removal rate (MRR), tool wear rate and radial over cut (ROC). Design/methodology/approach: The process variables considered in this study were powder types, powder concentration, tool materials, peak current and pulse on time. The experimental design, based on Taguchi’s L27 orthogonal array, was adopted to conduct experiments. Significant parameters were identified by performing the analysis of variance on the experimental data. Findings: Based on the analysis of results, it was observed that copper tool combined with Al powder produced maximum MRR (58.35 mm3/min). Similarly, the Al2O3 powder combined with tungsten tool has resulted least ROC (0.04865 mm). It was also observed that wear rate of tungsten tool was very low (0.0145 mm3/min). Originality/value: The experimental investigation of PMEDM involving three different powders (Al, SiC and Al2O3) was not attempted before. Moreover, the study of influence of different tool materials (Cu, brass and W) together with the different powders on the electric discharge machining performance was very limited.

1 January 2018 in Materials Today: Proceedings
Verified
Journal Article
Closed access
MJM. P. Jenarthanan
M. P. Jenarthanan
RSRAMESH KUMAR SUBRAMANIAN
RAMESH KUMAR SUBRAMANIAN
GVG. Venkatesh
G. Venkatesh
SNS. Nishanthan
S. Nishanthan