In this experimental work, a conus impacts a deep liquid pool at a speed varying from 1.3 to $19.0\ {\rm cm}\ {\rm s}^{-1}$ . Two liquids (2.5 % butanol–water solution or distilled water) and four coni made from duralumin with a diameter of 180 mm and different deadrise angles $\beta$ ( $2^{\circ }$ , $3^{\circ }$ , $4^{\circ }$ and 5 $^{\circ }$ ) are tested. An air cushion is trapped between the conus solid surface and the liquid. Several types of bubble patterns after the collapse of the air cushion are observed: one or multiple bubbles near the conus centre (vertex), irregular trails of bubbles on the conus surface and a ring of bubbles in a ‘necklace’-shaped arrangement. With a total internal reflection set-up and appropriate image post-processing, the external and internal radii of the ring-shaped wetted area are estimated for each frame. The external (internal) radius increases (decreases) in time following a linear (exponential) law. The speed of the outer border of the wetted area is in agreement with the Wagner theory for a body impacting onto a liquid. The initial radius of the annular touchdown region is estimated as the intersection of the relevant fitting curves. In the studied range of parameters, the initial radius obeys a universal scaling law, which follows from the air–water lubrication–inertia balance.
1 December 2024 in Journal of Applied Mechanics and Technical Physics
A setup for experimental studies of the structure, shape, and size of the gas–liquid interface under ultrasonic exposure and forced aeration has been developed. It has been found that ultrasonic exposure leads to an about 1.5-fold increase in interfacial area during aeration. The ultrasound intensity has been shown to have an optimal value that provides a maximum increase in interfacial area per unit ultrasonic energy input.
1 July 2021 in Journal of Applied Mechanics and Technical Physics
An oblique impact of a spherical segment with a curvature radius of 106.5 mm onto a water layer 20 mm thick is studied up to the instant of the body–liquid contact. The range of the impact angle with respect to the horizontal plane is 90–15°, and the vertical component of velocity for all angles is 10 or 20 mm/s. The measurements are performed by a synthetic schlieren method. The marker displacements are measured by a PTV algorithm. Distributions of the liquid layer thickness in space and time along two horizontal axes are obtained. It is shown that a change in the impact angle does not alter the dynamics of crater deepening and expansion at the initial stage; the crater remains axisymmetric. It is found that the rear slope of the crater becomes steeper in the case with the maximum deviation of the angle from the vertical line, presumably, because of the local decrease in pressure. The characteristics of capillary waves generated by the impact are independent of the impact angle.
An experimental study of quasi-two-dimensional liquid foams with varying liquid fractions is presented. Experiments are conducted in a Hele-Shaw cell with a local permeable obstacle placed in the center and filling 35, 60 and 78% of the cell gap. Foam velocity is calculated using a standard cross-correlation algorithm. Estimations of the liquid fraction of the foam are performed using a new simplified method based on a statistical analysis of foam cell structures. The pattern of the foam velocity field varies with increasing liquid fraction, responsible for significant variation of the foam’s rheology. The local permeability decreases with increasing obstacle height and liquid fraction. In case of high liquid fraction (), the permeability coefficient tends to zero for obstacles filling more than 78% of the cell gap.
An air bubble is injected into a liquid near the surface of an ultrasonic transducer and exposed to an ultrasonic field to increase the surface of the bubble–liquid interface. The purpose of this theoretical and experimental work is to investigate the effect of liquid viscosity on the relative increase in the bubble–liquid interface with ultrasonic cavitation. Numerically, the estimation of the relative increase in the air bubble surface is based on an iterative process. The distance between the air bubbles and the transducer, as well as the liquid viscosity, greatly impacts the surface relative increase. The optimal distance from the transducer is approximately 10 mm. At low viscosity, the surface area can increase by up to 1.7 times, but as the liquid viscosity increases above 7 mPa s, there is no significant increase. Experimentally, air bubbles subjected to ultrasonic cavitation are observed and analyzed. The image analysis algorithm is based on analyzing the external contour of the bubble combined with the brightness gradients in the image. The experimental observations are similar to those observed numerically. The relative increase in the surface area decreases with the viscosity. Above a viscosity of approximately 7.4 mPa s, there is almost no further relative increase.
In this experimental work, a two-dimensional (wedge) and three-dimensional solids (conus, 4 and 6-sided pyramids) with different deadrise angles (1– $5^\circ$ ) impact a deep liquid pool (distilled water or 2.5 % butanol–water solution) at a speed varying from 0.50 to 19.75 cm s −1 . Below a limit speed dependent on the deadrise angle, ‘exotic’ terminal forms of air entrapment are observed: a large central bubble, two parallel lines of bubbles for the two-dimensional solid, a trail of bubbles, necklace of bubbles, doughnut-shaped bubble and large central bubble for the three-dimensional solids. Above this limit speed, the collapse of the air film forms a line of bubbles near the central edge for the two-dimensional solid, and one/multiple bubbles near the vertex for the three-dimensional solids. The entrapment dynamic is observed using a high-speed camera with a total internal reflection set-up. The outer border of the wetted area expands linearly in time, with a speed that agrees with Wagner’s theory for wedge and conus, which provides the lower and upper limites for genuinely three-dimensional cases (pyramids). The decrease in the size of the air film over time is exponential. The measured initial characteristic size of the air film is proportional to the air dynamic viscosity and inversely proportional to the liquid density, impact velocity and squared deadrise angle, as expected from an air–water lubrication–inertia balance. The prefactor in the scaling law depends on the shape of the solid with a slight but detectable effect of liquid surface tension on its value.