A 2D scanning micromirror with piezoelectric thin film aluminum nitride (AlN), separately used as actuator and sensor material, is presented. For endoscopic applications, such as fluorescence microscopy, the devices have a mirror plate diameter of 0.7 mm with a 4 mm2 chip footprint. After an initial design optimization procedure, two micromirror designs were realized. Different spring parameters for x- and y-tilt were chosen to generate spiral (Design 1) or Lissajous (Design 2) scan patterns. An additional layout, with integrated tilt angle sensors, was introduced (Design 1-S) to enable a closed-loop control. The micromirror devices were monolithically fabricated in 150 mm silicon-on-insulator (SOI) technology. Si (111) was used as the device silicon layer to support a high C-axis oriented growth of AlN. The fabricated micromirror devices were characterized in terms of their scanning and sensor characteristics in air. A scan angle of 91.2° was reached for Design 1 at 13 834 Hz and 50 V. For Design 2 a scan angle of 92.4° at 12 060 Hz, and 123.9° at 13 145 Hz, was reached at 50 V for the x- and y-axis, respectively. The desired 2D scan patterns were successfully generated. A sensor angle sensitivity of 1.9 pC/° was achieved.
Piezoelectric micromirrors with aluminum nitride (AlN) and aluminum scandium nitride (Al0.68Sc0.32N) are presented and compared regarding their static deflection. Two chip designs with 2 × 3 mm2 (Design 1) and 4 × 6 mm2 (Design 2) footprint with 600 nm AlN or 2000 nm Al0.68Sc0.32N as piezoelectric transducer material are investigated. The chip with Design 1 and Al0.68Sc0.32N has a resonance frequency of 1.8 kHz and a static scan angle of 38.4° at 400 V DC was measured. Design 2 has its resonance at 2.1 kHz. The maximum static scan angle is 55.6° at 220 V DC, which is the maximum deflection measurable with the experimental setup. The static deflection per electric field is increased by a factor of 10, due to the optimization of the design and the research and development of high-performance piezoelectric transducer materials with large piezoelectric coefficient and high electrical breakthrough voltage.
19 February 2004 in Semiconductor Science and Technology
This paper presents a technique for selective and energy-efficient induction heating of aluminum (Al) frames to support and enhance the thermocompression bonding (TCB) for electronics packaging in the field of heterogeneous integration. The technological challenges include the use of an adapted induction coil for homogeneous heat distribution, the implementation of ISM (industrial, scientific, medical) radio band frequencies in the high frequency (HF) and very high frequency (VHF) range up to f 0 = 40.68 MHz, and the assembly of a heating system based on an RF generator and automatic matching unit for impedance modulation. Finite element analysis (FEA) was used to calculate the electromagnetic (EM) fields based on the coil design used. The inductive heating was successfully carried out using a generator power of P = 100 W with coil currents in the range of I 0 = 10.1 to 11.3 A (amplitudes). With this setup, a peak temperature of T f_max = 633 °C in the Al frames could be achieved after th = 10 s. This corresponds to an average heating rate of dT/dt = 63.3 K/s.
Considering the demand for low temperature bonding in 3D integration and packaging of microelectronic or micromechanical components, this paper presents the development and application of an innovative inductive heating system using micro coils for rapid Cu-Sn solid-liquid interdiffusion (SLID) bonding at chip-level. The design and optimization of the micro coil as well as the analysis of the heating process were carried out by means of finite element method (FEM). The micro coil is a composite material of an aluminum nitride (AlN) carrier substrate and embedded metallic coil conductors. The conductive coil geometry is generated by electroplating of 500 µm thick copper into the AlN carrier. By using the aforementioned micro coil for inductive Cu-Sn SLID bonding, a complete transformation into the thermodynamic stable ε-phase Cu3Sn with an average shear strength of 45.1 N/mm2 could be achieved in 130 s by applying a bond pressure of 3 MPa. In comparison to conventional bonding methods using conduction-based global heating, the presented inductive bonding approach is characterized by combining very high heating rates of about 180 K/s as well as localized heating and efficient cooling of the bond structures. In future, the technology will open new opportunities in the field of wafer-level bonding.
In this article, an efficient die-bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles, and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, finite element (FE) simulation methods were applied to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests to qualify the inductive bonding technology. The results presented in this paper demonstrate that induction heating has high potential for cost-effective production in the field of die attach and can drastically increase the output in power-electronics production.