Ivo Jebáček

Prof. Ivo Jebáček

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 June 2012 in Aviation
Verified
Journal Article
Open access
IJIvo Jebáček
Ivo Jebáček
MHMarek Horak
Marek Horak
This article provides information about in-flight measurement of a small sport aircraft. First strain gauges were installed in the wing structure and then calibration procedures were done. After the calculation of strain gauge coefficients, equations for calculating bending moments and other variables were established. A data acquisition system was installed in the aircraft to measure responses from strain gauges and other variables such as speed, altitude, load factor, and temperature. Many flights were performed with the aircraft equipped this way, and after that the recorded data were analysed and those results were compared with the calculations and static strength tests performed before.

14 April 2020 in Aircraft Engineering and Aerospace Technology
Verified
Journal Article
Closed access
PZPavel Zikmund
Pavel Zikmund
MHMichaela Horpatzká
Michaela Horpatzká
LDLukáš Dubnický
Lukáš Dubnický
MMMiroslav Macík
Miroslav Macík
IJIvo Jebáček
Ivo Jebáček
Purpose: The purpose of this study is to lead to an improvement in pilot-aircraft interaction. The goal of the performed tests is an assessment of haptic feedback, which mediates flight parameters to the pilot. Pedals indicate side-slip angle by vibrations, whereas a sliding element inside the control stick is able to continuously indicate both angles of attack and side-slip. Design/methodology/approach: Haptic feedback applied on rudder pedals and control stick were tested on a flight simulator and flight tests in a couple of tasks. Pilot workload, readability of feedback and side-slip were then evaluated when the flight was turning. Findings: As a useful instrument for aircraft control, haptic feedback was assessed. The feedback settings were then individually perceived, and haptic feedback slightly improved side-slip while turning in a flight test; however, the results are not statistically significant. Practical implications: The tests provided promising results for human pilot performance. The training phase and personal settings of haptic feedback is an approach for improving the performance of human pilots. Originality/value: The designed and tested device is a unique tool for improving pilot-aircraft interaction. This study brings valuable experiences from its flight simulator and in-flight tests. Peer review: The peer review history for this article is available at: https://publons.com/publon/10.1108/AEAT-12-2019-0265/

14 January 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
RGRobert Grim
Robert Grim
RPRobert Popela
Robert Popela
IJIvo Jebáček
Ivo Jebáček
MHMarek Horák
Marek Horák
JŠJan Šplíchal
Jan Šplíchal
This article evaluates the redistribution of forces to the parachute harness during an opening shock load and also defines the ultimate limit load of the personal parachute harness by specifying the weakest construction element and its load capacity. The primary goal of this research was not only to detect the critical elements but also to gain an understanding of the force redistribution at various load levels, which could represent changes in body mass or aerodynamic properties of the parachute during the opening phase. To capture all the phenomena of the parachutist’s body deceleration, this study also includes loading the body out of the steady descending position and asymmetrical cases. Thus, the result represents not only idealized loading but also realistic limit cases, such as asymmetric canopy inflation or system activation when the skydiver is in a non-standard position. The results revealed a significant difference in the strength utilization of the individual components. Specifically, the back webbing was found to carry a fractional load compared to the other webbing used in the design in most of the scenarios tested. Reaching the maximum allowable strength was first achieved in the asymmetric load test case, where the total force would be equal to the value of 7.963 kN, which corresponds to the maximum permissible strength of the carabiner on the measuring element three. In the same test case, the second weakest point would reach the limiting load force when the entire harness is loaded with 67.89 kN. This information and the subsequent analysis of the individual nodes provide a great opportunity for further strength and weight optimization of the design, without reducing the load capacity of the harness as a system. The findings of this study will be used for further testing and possible harness robustness optimization for both military and sport parachuting.

31 August 2026 in Engineering Failure Analysis
Verified
Journal Article
Open access
MSMartin Sladký
Martin Sladký
Jan PapugaJan Papuga
Jan Papuga
MMMartin Machač
Martin Machač
IJIvo Jebáček
Ivo Jebáček

22 January 2020 in Aviation
Verified
Journal Article
Open access
PDF file
TKTomáš Katrňák
Tomáš Katrňák
JJJaroslav Juračka
Jaroslav Juračka
IJIvo Jebáček
Ivo Jebáček
This article presents further results of the research of effects of model defects on the local buckling of compressed stiffeners in nonlinear finite element (FE) analyses. The main outcomes are confirmation of trends for 10 sets of profile dimensions, final validations of various sets of FE simulations, and designs of practical types of defects with appropriate ratio values. A single node defect and then complex types of defects with alternating distributions of node shifts along one edge, two free flange edges, one flange surface and both flange surfaces are analyzed in this research project. First parts of this paper describe designed FE models with defects, their effects on simulation results, colored graphic visualizations with stress scales and determinations of the sudden failure of stability in the local mode. Then, particular results of FE analyses are validated by a comparison with the results of analytical methods of stability failure. Final detail comparisons of analytical and FE simulation results with data of experimental tests confirm predicted critical buckling forces. The validation of results and design parameters together with the knowledge of effects of model defects on buckling behaviors allows more accurate simulations of internal stiffeners of thin-walled semi-monocoque structures.

21 January 2026 in Composite Structures
Verified
Journal Article
Open access
VHVladimír Hostinský
Vladimír Hostinský
JSJurij Sodja
Jurij Sodja
IJIvo Jebáček
Ivo Jebáček
JNJan Navrátil
Jan Navrátil