Nerita Žmuidzinavičienė

Dr. Nerita Žmuidzinavičienė


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 July 2022 in Journal of Environmental Management
Verified
Journal Article
Closed access
VAV. Abromaitis
V. Abromaitis
JSJ. Svaikauskaite
J. Svaikauskaite
Agnė ŠulčiūtėAgnė Šulčiūtė
Agnė Šulčiūtė
DSD. Sinkeviciute
D. Sinkeviciute
Nerita ŽmuidzinavičienėNerita Žmuidzinavičienė
Nerita Žmuidzinavičienė
DMD. Martuzevicius
D. Martuzevicius

30 July 2021 in Processes
Verified
Journal Article
Open access
PDF file
AKArnas Klevinskas
Arnas Klevinskas
KKKristina Kantminienė
Kristina Kantminienė
Nerita ŽmuidzinavičienėNerita Žmuidzinavičienė
Nerita Žmuidzinavičienė
IJIlona Jonuskiene
Ilona Jonuskiene
Egidijus GriskonisEgidijus Griskonis
Egidijus Griskonis
The deteriorating environmental quality requires a rapid in situ real-time monitoring of toxic compounds in environment including water and wastewater. One of the most toxic nitrogen-containing ions is nitrite ion, therefore, it is particularly important to ensure that nitrite ions are completely absent in surface and ground waters as well as in wastewater or, at least, their concentration does not exceed permissible levels. However, no selective ion electrode, which would enable continuous measurement of nitrite ion concentration in wastewater by bioelectrochemical sensor, is available. Microbial fuel cell (MFC)-based biosensor offers a sustainable low-cost alternative to the monitoring by periodic sampling for laboratory testing. It has been determined, that at low (0.01–0.1 mg·L−1) and moderate (1.0–10 mg·L−1) concentration of nitrite ions in anolyte-model wastewater, the voltage drop in MFC linearly depends on the logarithm of nitrite ion concentration of proving the potential of the application of MFC-based biosensor for the quantitative monitoring of nitrite ion concentration in wastewater and other surface water. Higher concentrations (100–1000 mg·L−1) of nitrite ions in anolyte-model wastewater could not be accurately quantified due to a significant drop in MFC voltage. In this case MFC can potentially serve as a bioelectrochemical early warning device for extremely high nitrite pollution.

15 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
AIArminas Ilginis
Arminas Ilginis
Nerita ŽmuidzinavičienėNerita Žmuidzinavičienė
Nerita Žmuidzinavičienė
Egidijus GriskonisEgidijus Griskonis
Egidijus Griskonis
One of the possible ways of mitigating the primary lead-acid battery downside—mass— is to replace the heavy lead grids that can add up to half of the total electrode’s mass. The grids can be exchanged for a lightweight, chemically inert, and conductive material such as graphite felt. To reduce carbon surface area, Pb/PbO2 can be electrochemically deposited on graphite felt. A flow-through reactor was applied to enhance penetration of adequate coverage of graphite felt fibers. Three types of electrolytes (acetate, nitrate, and methanesulfonate) and two additives (ligninsulfonate and Triton X-100) were tested. The prepared composite electrodes showed greater mechanical strength, up to 5 times lower electrical resistivity, and acted as Pb and PbO2 electrodes in sulfuric acid electrolytes.

15 September 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Nerita ŽmuidzinavičienėNerita Žmuidzinavičienė
Nerita Žmuidzinavičienė
Egidijus GriskonisEgidijus Griskonis
Egidijus Griskonis
Algirdas ŠulČiusAlgirdas ŠulČius
Algirdas ŠulČius
Manganese coatings are excellent for the cathodic protection of steel against corrosion. Although manganese is more electrochemically active than widely used protective coatings of zinc, the exceptional resistance of manganese coatings in neutral and basic media is determined by the film of insoluble corrosion products, which forms on the surface of manganese and greatly suppresses its further corrosion. It is known that the electrodeposition process of Mn coatings from sulphate electrolytes is positively affected by some additives of chalcogenide (S, Se and Te) compounds in the electrolyte. However, a more detailed study on the corrosion properties of Mn coatings electrodeposited from sulphate bath with Te(VI) additive is lacking. In this work, the measurements of free corrosion potential and potentiodynamic polarization in a neutral NaCl solution, as well as the corrosion resistance properties of obtained Mn coatings, were evaluated in a salt spray chamber. It was obtained that the best corrosion resistance was shown by Mn coatings, electrodeposited at the cathodic current density of 15 A⋅dm−2 and at higher temperatures (60 and 80 °C). Meanwhile, the corrosion resistance of phosphated Mn coatings, obtained from a room temperature bath, increased about 5 times and reached up to 1000 h until corrosion of the steel substrate occurred.

4 July 2026 in Coatings
Verified
Journal Article
Open access
PDF file
VSVasaris Statkevičius
Vasaris Statkevičius
Egidijus GriskonisEgidijus Griskonis
Egidijus Griskonis
Nerita ŽmuidzinavičienėNerita Žmuidzinavičienė
Nerita Žmuidzinavičienė
As a chemical element, manganese is used in a wide range of industries, particularly steelmaking and creating alloys and as a sacrificial coating for corrosion protection. Electrodeposition is a low-energy process; however, manganese electrodeposition from aqueous solutions remains challenging due to the highly negative reduction potential of Mn2+. The addition of group VI elements such as selenium, sulfur or tellurium to the electrolyte improves both coating quality and the current efficiency of manganese electrodeposits by suppressing the competing hydrogen evolution reaction (HER). While selenium and sulfur compounds are widely studied electrolyte additives, research on the use of tellurium additives in the electrolyte and their influence on the manganese electrodeposition process and subsequent coating properties remains limited. In this work, manganese electrodeposits were obtained from a manganese ammonium sulfate bath (MASB) electrolyte with a sodium tellurate(VI) additive at both room and elevated temperatures. The resulting coatings, which also underwent a phosphating process to enhance the corrosion resistance of the coating, were investigated for properties such as morphology, elemental composition, and corrosion resistance; all corrosion tests were carried out in a 3% NaCl solution. The findings show that coatings deposited at higher temperatures exhibit a more compact surface structure, with α-Mn becoming more abundant as the MASB temperature increases. Furthermore, higher-temperature deposition produces coatings with greater current efficiency, though at the cost of a higher concentration of incorporated tellurium. Finally, the coatings that underwent the phosphating were evaluated against untreated (uncoated and non-phosphated) mild carbon steel regarding their corrosion resistance.