This paper presents a comparative analysis of supercapacitors and batteries as energy storage technologies, focusing on key performance metrics such as energy storage capacity, power output, efficiency, and charge/discharge cycles. Supercapacitors are known for their rapid charge and discharge capabilities, high power density, and longevity, making them ideal for applications requiring quick bursts of energy. Conversely, batteries, particularly lithium-ion, offer significantly higher energy density, enabling them to store more energy in a compact form factor, but they suffer from longer charging times and limited cycle life. This study highlights the trade-offs between the two technologies, providing insights into their suitability for various applications, from consumer electronics to renewable energy systems. The findings suggest that while supercapacitors excel in scenarios demanding high power and durability, batteries remain the preferred choice for applications requiring higher energy storage capacity. The analysis underscores the importance of selecting the appropriate energy storage solution based on specific application requirements.
1 February 2019 in Journal of Electrical Engineering
This paper studies an improved fractional order parallel control structure (FOPCS) for enhancing the robustness in an industrial control loop having a first order process with dead time along with its tuning aspects. Since inclusion of fractional order calculus also increase the number of parameters to be determined for a particular control loops, tuning becomes an essential task. Four different tuning methods are considered to optimize the gains of parallel control structure (PCS) and FOPCS. Integral of time weighted absolute error for servo and regulatory problems along with overshoot value have been considered for performance evaluation. Extensive simulation studies including change in setpoint and mismatch in processmodel parameters have been carried out. On the basis of these studies, it was observed that FOPCS tuned by backtracking search algorithm, outperformed all other controllers in terms of considered performance measures.
This paper includes a design analysis of an inductorless low-power (LP) low-noise amplifier (LNA) with active load for Ultra Wide Band (UWB) applications. The proposed LNA consists of two parallel paths, one is the common source (CS) path and second is the CG path. The CG path has the edge advantage of improving overall Noise figure (NF) due to wide band impedance matching in UWB, while the CS path provides high power gain. A method for noise cancellation is adopted, to reduce the noise of CS path with the help of CG path. The proposed LNA successfully simulated in 90 nm CMOS technology. The results of proposed work indicate optimization at frequency 5.70 GHz with 3 dB bandwidth of 4.3 GHz–8.9 GHz. All simulations have been done for a range of frequency 03 GHz–13 GHz in Cadence virtuoso software. The results quoted 1.15 dB NF, −18.12 dB S11, 13.7 dB S21, maximum operating power gain (GP) 11.756 dB at frequency 5.7 GHz and available power gain (GA) is 10.17 dB at frequency 8.61 GHz, with 0.6 V, 0.92 mW broad band LNA.
28 August 2017 in Journal of Electrical Engineering
In the last years, Interleave Division Multiple Access (IDMA) has been presented as a potential alternate of Code Division Multiple Access (CDMA) system. In IDMA systems, the interleavers are used to separate the users of the system in multiple access environments. Random interleaver is popular and basic taxonomy, which scrambles information bits of craving users with different patterns. However the indispensable characteristics of a random interleaver such as bandwidth requirement, computational complexity, and memory restraint at both transmitter and receiver end is uttermost. Further, it has also been observed that the study of role of chaos in interleaver design is very limited in literature. Hence, in this paper, a low complexity chaos based interleaver named as modified Tent map interleaver is designed for further performance improvement of IDMA system and the characteristic parameters are compared with the random interleaver. The IDMA system model uses a BPSK modulation and repetition coder with a code rate of 1/2. The system is simulated in MATLAB and results show that the better BER performance without the need of extra memory resources.
The power system for large-scale adoption of hybrid electric vehicles can benefit from a distributed reserve provided by the vehicle-to-grid (V2G) concept. This study suggests a V2G technology that can effectively control frequency on a microgrid throughout a 24-h cycle. When usage is at its lowest in the spring or fall, a microgrid is intended to be large enough to simulate a community of 2000 households. A 1:5 ratio of cars to households is realized by modelling 400 electric vehicles (EVs) as a basic model, indicating a typical case in the future. An in-depth analysis of the voltage, current, reactive, and active power is carried out for a microgrid. By coordinating control of diesel generation, renewable energy source (RES) generation, power exchange, and EV generation, the system frequency of a microgrid can be managed by regulating load demand with V2G devices. The proposed microgrid with V2G effectively manages energy and reduces the uncertain and variable nature of RES power generation with enhanced performance. System parameter variations have been investigated for various operating scenarios, and it has been discovered that error is confined to less than 5%.