This paper explains the working principles, supported by simulation results, of a new converter topology intended for HVDC applications, called the alternate arm converter (AAC). It is a hybrid between the modular multilevel converter, because of the presence of H-bridge cells, and the two-level converter, in the form of director switches in each arm. This converter is able to generate a multilevel ac voltage and since its stacks of cells consist of H-bridge cells instead of half-bridge cells, they are able to generate higher ac voltage than the dc terminal voltage. This allows the AAC to operate at an optimal point, called the “sweet spot,” where the ac and dc energy flows equal. The director switches in the AAC are responsible for alternating the conduction period of each arm, leading to a significant reduction in the number of cells in the stacks. Furthermore, the AAC can keep control of the current in the phase reactor even in case of a dc-side fault and support the ac grid, through a STATCOM mode. Simulation results and loss calculations are presented in this paper in order to support the claimed features of the AAC.
25 November 2013 in IEEE Transactions on Power Electronics
Voltage ratings for HVdc point-to-point connections are not standardized and tend to depend on the latest available cable technology. DC/DC conversion at HV is required for interconnection of such HVdc schemes as well as to interface dc wind farms. Modular multilevel voltage source converters (VSCs), such as the modular multilevel converter (MMC) or the alternate arm converter (AAC), have been shown to incur significantly lower switching losses than previous two- or three-level VSCs. This paper presents a dc/ac/dc system using a transformer coupling two modular multilevel VSCs. In such a system, the capacitors occupy a large fraction of the volume of the cells but a significant reduction in volume can be achieved by raising the ac frequency. Using high frequency can also bring benefits to other passive components such as the transformer but also results in higher switching losses due to the higher number of waveform steps per second. This leads to a tradeoff between volume and losses which has been explored in this study and verified by simulation results with a transistor level model of 30-MW case study. The outcome of the study shows that a frequency of 350 Hz provides a significant improvement in volume but also a penalty in losses compared to 50 Hz.
Multilevel converters, such as the modular multilevel converter (MMC) or the alternate arm converter (AAC), rely on charged capacitors in their cells to generate their AC voltage waveform. Since the cell capacitors are physically large and occupy approximately half the cell volume, their capacitance must be kept minimal while limiting the voltage fluctuation caused by the current passing periodically through these capacitors. This study proposes a mathematical model which estimates the energy deviation for the stacks of both the MMC and the AAC during steady‐state operation under any power factor and for AC voltage magnitude fluctuation of up to ±10%. The analysis is then used to calculate the minimum size for the cell capacitors in order to keep their voltage fluctuation within set boundaries for both topologies. The results show that the MMC requires 39 kJ/MVA of capacitive energy storage under sinusoidal modulation but this reduces with triplen injection modulation. The AAC has a lower requirement for storage in its cells of 11 kJ/MVA but the AAC has a six‐pulse DC current ripple which requires a filter estimated to have a further 33% capacitive storage.
23/04/13 meb. Email sent asking for copyright and permission to add to spiral since its conference.. 24/04 emails ent requesting permission. 25/04/13 Meb Permission granted, ready to pub.Voltage-Source Converters have brought numerous advantages to HVDC transmission. However, they suffer from high losses and are usually weak against faults on the DC-side. In this paper, a new topology which brings together some concepts from traditional Current Source Converters and multi-level converters, is presented. Two stacks of H-bridge cells alternate to construct the converter voltage using director switches made of IGBTs in series. The resulting converter generates AC current with low harmonic content and with low loss. Furthermore, the converter is still very responsive in case of a fault. This paper first explains the composition and the working of this converter, then detailed simulations at 20 MW illustrate the performances and low losses of this converter under normal conditions. The ability of this topology to deal with abnormal conditions is also demonstrated, especially its ability to keep control of the current despite the collapse of the DC bus voltage, e.g. a DC-side fault
3 August 2017 in IEEE Transactions on Power Electronics
The alternate arm converter (AAC) was one of the first modular converter topologies to feature dc-side fault ride-through capability with only a small penalty in power efficiency. However, the simple alternation of its arm conduction periods (with an additional short overlap period) resulted in 1) substantial six-pulse ripples in the dc current waveform, 2) large dc-side filter requirements, and 3) limited operating area close to an energy sweet spot. This paper presents a new mode of operation called extended overlap (EO) based on the extension of the overlap period to 60°, which facilitates a fundamental redefinition of the working principles of the AAC. The EO-AAC has its dc current path decoupled from the ac current paths, a fact allowing 1) smooth dc current waveforms, 2) elimination of dc filters, and 3) restriction lifting on the feasible operating point. Analysis of this new mode and EO-AAC design criteria are presented and subsequently verified with tests on an experimental prototype. Finally, a comparison with other modular converters demonstrates that the EO-AAC is at least as power efficient as a hybrid modular multilevel converter (MMC) (i.e., a dc fault ride-through-capable MMC), while offering a smaller converter footprint because of a reduced requirement for energy storage in the submodules and a reduced inductor volume.
This paper presents a method to calculate the minimal size of cell capacitors in multilevel VSCs which meets a maximum voltage deviation criterion under ideal conditions. This method is applied to the Modular Multilevel Converter (MMC), the Alternate Arm Converter (AAC) and the hybrid multilevel converter with ac-side cascaded H-bridge cells (AC-CHB). The results show that the newer VSC topologies exhibits smaller energy deviation in their stacks, leading to an overall smaller volume of cell capacitors for the converter station but often accompanied by some compromises such as higher power losses or degraded DC current waveform quality.