Katrin Böttcher

Dr. Katrin Böttcher

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
KBKatrin Böttcher
Katrin Böttcher
Mayka Schmitt RahnerMayka Schmitt Rahner
Mayka Schmitt Rahner
USUlf Stolzenberg
Ulf Stolzenberg
SKSebastian Kraft
Sebastian Kraft
Jörn BonseJörn Bonse
Jörn Bonse
Jörg KrügerJörg Krüger
Jörg Krüger
Ultrashort pulse laser processing can result in the secondary generation of unwanted X-rays if a critical laser irradiance of about 1013 W cm−2 is exceeded. Spectral X-ray emissions were investigated during the processing of tungsten and steel using three complementary spectrometers (based on CdTe and silicon drift detectors) simultaneously for the identification of a worst-case spectral scenario. Therefore, maximum X-ray photon energies were determined, and corresponding dose equivalent rates were calculated. An ultrashort pulse laser workstation with a pulse duration of 274 fs, a center wavelength of 1030 nm, pulse repetition rates between 50 kHz and 200 kHz, and a Gaussian laser beam focused to a spot diameter of 33 μm was employed in a single pulse and burst laser operation mode. Different combinations of laser pulse energy and repetition rate were utilized, keeping the average laser power constant close to the maximum power of 20 W. Peak irradiances I0 ranging from 7.3 × 1013 W cm−2 up to 3.0 × 1014 W cm−2 were used. The X-ray dose equivalent rate increases for lower repetition rates and higher pulse energy if a constant average power is used. Laser processing with burst mode significantly increases the dose rates and the X-ray photon energies. A maximum X-ray photon energy of about 40 keV was observed for burst mode processing of tungsten with a repetition rate of 50 kHz and a peak irradiance of 3 × 1014 W cm−2.

23 July 2025 in Applied Physics A
Verified
Journal Article
Open access
PDF file
KBKatrin Böttcher
Katrin Böttcher
SKSebastian Kraft
Sebastian Kraft
MWMatthias Weise
Matthias Weise
Jörn BonseJörn Bonse
Jörn Bonse
Jörg KrügerJörg Krüger
Jörg Krüger
Ultrashort pulse lasers offer the possibility to process materials with minimal heat input and high precision. However, the X-ray emission at high laser peak intensities represents an undesirable side effect. A laser system (1030 nm wavelength, 40 W maximum average laser power, 925 fs pulse duration, 100 μJ maximum pulse energy, 400 kHz pulse repetition frequency) was used to analyze the X-ray skin dose rates for applied peak intensities between 9.2 × 1012 W/cm2 and 1.3 × 1014 W/cm2 for mild steel, stainless steel and tungsten during groove processing. The lowest laser peak intensity at which X-ray emission could be measured was 9.2 × 1012 W/cm2 for processing of stainless steel. The X-ray emission showed a characteristic evolution in dependence on the number of overscans at the same line positions. For low peak intensities, a measurable X-ray emission only begins after a few passes. The number of scans to reach the maximum dose rate increases with lower laser peak intensity. Analysis of the evolving surface topography by white light interference microscopy in connection with ray-tracing simulations led to the interpretation that the increase in X-ray emission is due to the local intensity redistribution by multiple reflection within the laser-generated grooves which is promoted by a particular choice of the linear laser polarization.

3 October 2025 in Applied Physics A
Verified
Journal Article
Open access
PDF file
KBKatrin Böttcher
Katrin Böttcher
SKSebastian Kraft
Sebastian Kraft
MWMatthias Weise
Matthias Weise
Jörn BonseJörn Bonse
Jörn Bonse
Jörg KrügerJörg Krüger
Jörg Krüger

1 July 2026 in Optics & Laser Technology
Verified
Journal Article
Open access
KBKatrin Böttcher
Katrin Böttcher
LNLucas Naumann
Lucas Naumann
RGRoswitha Giedl-Wagner
Roswitha Giedl-Wagner
JSJörg Schille
Jörg Schille
ULUdo Loeschner
Udo Loeschner
Jörg KrügerJörg Krüger
Jörg Krüger