Impellers are utilized to increase pressure to ensure that a radial pre-swirl system can provide sufficient cooling airflow to the turbine blades. In the open literature, the pressurization mechanism of the impellers was investigated. However, the effect of impellers on the cooling performance of the radial pre-swirl system was not clear. To solve the aforementioned problem, tests were carried out to assess the temperature drop in a radial pre-swirl system with various impeller configurations (impeller lengths l/b ranging from 0 to 0.333). Furthermore, numerical simulations were used to investigate the flow and heat transfer characteristics of the radial pre-swirl system at high rotating Reynolds numbers. Theoretical and experimental investigations revealed that the pre-swirl jet and output power generate a significant temperature drop, but the impellers have no obvious effect on the system temperature drop. By increasing the swirl ratio, the impellers reduce the field synergy angle and thus improve convective heat transfer on the turbine disk. In addition, increasing the impeller length can reduce the volume-averaged field synergy angle and improve heat transfer, but the improvement effectiveness decreases as the impeller length increases. Thus, the study concluded that impellers could improve the cooling performance of the radial pre-swirl system by enhancing disk cooling.
Complex oil and gas two-phase flow exists within an aero-engines bearing cavity scavenge pipe, prone to lubricated self-ignition and coking. Lubricant system designers must be able to accurately identify and understand the flow state of the scavenge pipe. The prediction accuracy of previous models is insufficient to meet the more demanding needs. This paper establishes a visualized flow pattern identification test system for the scavenge pipe, with a test temperature of up to 370 k, using a high-speed camera to photograph four flow patterns, decomposing the pressure signals obtained from high-frequency dynamic pressure sensors using the ensemble empirical mode decomposition (EEMD) method, and then performing Hilbert transform, using the Hilbert spectrum to quantify the changes of amplitude and frequency with time, and establishing the energy and flow pattern correspondence analysis. Then the energy percentage of IMFs is used as the input of feature values, and the random forest algorithm machine learning is used for predictive classification. The experimental results show that the flow pattern recognition rate established in this paper can reach 98%, which can identify the two-phase flow pattern in the scavenge pipe more objectively and accurately.
The lubricating oil system is a significant component of aviation engine lubrication and cooling, and the scavenge pipe is an essential component of the lubricating oil system. Accurately identifying and understanding the flow state of the scavenge pipe is very important. This article establishes a visualization test bench for a 45-degree inclined scavenge pipe, with upward and downward flow directions, respectively. The test temperature is 370 K, and a high-speed camera captures the changes in the two-phase flow inside the pipeline. Based on high-speed photography photos, we develop software for analyzing the flow characteristics of bubbles inside the tube and explore the influence of gas phase conversion velocity and liquid phase conversion velocity on the apparent velocity of bubbles inside the tube. Multiple algorithms were used to develop the model by combining machine learning with speed and accuracy to establish a data regression prediction model for the apparent velocity of bubbles inside the tube. Through calculation and analysis, it was found that the root mean square error of the prediction model using the BP neural network algorithm was the lowest, and the decision coefficient of the prediction model using the support vector machine algorithm was the highest.
In the modern aerospace industry, the importance of a lubrication system is self-evident for aero-engines, and the aero-engine bearing chamber return line is an even more challenging environment, as it involves a complex two-phase flow. The designer of the scavenge pipe needs to have an accurate understanding of the flow conditions in the scavenge pipe. This paper establishes a visual scavenge pipe test system. The flow direction was vertical flow, the test temperature was 370 k, and a high-speed camera was used to take high-definition flow photographs, which can observe the three main flow types: bubble flow, slug flow, and annular flow. Code program was created to analyze many pictures taken to obtain the apparent flow rate and perimeter of bubbles in the pipe under different flow conditions and to explore the gas–liquid two-phase flow in the scavenge pipe. A support vector machine (SVM) was used for data regression prediction, and the converted velocities of the gas–oil phases were inputted as eigenvalues to obtain the predicted values of bubble-flow velocity. The bubble-flow analysis prediction model established in this paper has a good prediction effect with root mean square error RMSE = 0.0172, which can more objectively and accurately describe the bubble-flow characteristics in the scavenge pipe.