Hong Shen

Dr. Hong Shen

School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, China

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2017 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
CZChi Zhang
Chi Zhang
JZJing Zhou
Jing Zhou
Hong ShenHong Shen
Hong Shen
As one of emerging novel surface treatment techniques, laser polishing offers a cost-effective and efficient solution to reduce surface roughness of precision components at micro-/mesoscale. Although it has been applied for industrial and biomedical purposes, the underlying mechanism has not been fully revealed. This paper presents a study to understand the basic fundamentals of continuous wave fiber laser polishing of Ti6Al4V samples. A two-dimensional numerical model that coupled heat transfer and fluid flow is developed to illustrate the molten flow behavior. The roles of capillary and thermocapillary flow in the process of laser polishing are investigated to assist the understanding of the contributions of surface tension (capillary force) and Marangoni effect (thermocapillary force) in the polishing process. Capillary force dominates the molten pool at the initial stage of melting, while thermocapillary force becomes predominant when the molten pool fully develops.

28 February 2017 in Journal of Heat Transfer
Verified
Journal Article
Closed access
PDF file
Hong ShenHong Shen
Hong Shen
YPYanqing Pan
Yanqing Pan
JZJing Zhou
Jing Zhou
ZYZhenqiang Yao
Zhenqiang Yao

7 May 2020 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
Zhenyu LiuZhenyu Liu
Zhenyu Liu
XYXinyu Yao
Xinyu Yao
XCXiao Cheng
Xiao Cheng
HWHuiying Wu
Huiying Wu
HWHan Wang
Han Wang
Hong ShenHong Shen
Hong Shen
In this study, the sinusoidal wavy (SW) copper microchannels with triangular cross section were fabricated with the ultrafast laser micromachining approach. The flow boiling of de-ionized water in SW microchannels were experimentally studied under mass fluxes of 43.43–217.15 kg (m 2 s) −1 and heat fluxes of 0–590 kW m −2 . The flow patterns in the SW microchannels were visually observed and the boiling heat transfer characteristics were analyzed based on the obtained data. It shows the SW microchannel has a maximum enhancement of 127.7% in the local heat transfer coefficient with an acceptable increase of pressure loss compared to the straight one in the present work. In SW microchannels, a low degree of superheat can trigger the onset of nucleate boiling. A slow decreasing tendency of local heat transfer coefficient under a high effective heat flux or a high vapor quality was observed. The heat transfer mechanism of flow boiling in SW microchannels was analyzed based on the experimental visualization. Nucleate boiling and thin film evaporation are the dominant modes under different thermal boundary conditions. The flow boiling instability phenomenon in microchannels can be diminished using the wavy structures.

19 October 2016 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
Hong ShenHong Shen
Hong Shen
DFDecai Feng
Decai Feng
ZYZhenqiang Yao
Zhenqiang Yao
Laser drilling of alumina is a noncontact material processing method, which has great advantages over the traditional mechanical machining. However, the quality of laser drilling is still a challenge. In this study, a 2D transient model is developed to simulate the underwater laser drilling of alumina, considering the recoil pressure which is generated by adjusting the density of water. The distributions of the temperature, pressure, and velocity during the drilling process are examined. The numerical results show that the underwater-drilled hole with smaller taper is obtained compared with that in air, which is attributed to the recoil pressure, higher specific heat capacity, and heat transfer coefficient of water. The experimental results validate the phenomenon in numerical simulation.

1 December 2019 in Journal of Micro and Nano-Manufacturing
Verified
Journal Article
Closed access
PDF file
KZKai Zhao
Kai Zhao
HWHan Wang
Han Wang
JYJingwen Yan
Jingwen Yan
Hong ShenHong Shen
Hong Shen
Researches on glass welding using tightly focused ultrafast lasers have attracted much attention. However, optical systems with low numerical aperture (NA) in laser material processing are commonly used in industry applications. Transmission welding of two fused silica glass plates is performed by using picosecond laser irradiation with low NA in this study. The welding strength under different process parameters such as focal position, pulse energy, and scanning velocity is measured. The role of the modification in welding process is demonstrated through the interior morphology in single-piece glass samples. A model is presented to predict the position of the bottom tip of the modification (BTM). The model considers the propagation property of the laser beam and the incubation effect of modification threshold. The numerical and experimental positions of BTM are compared. The model can give an idea for selecting process parameters to the achievement of glass welding for low NA optical system in ultrafast laser welding.

1 July 2019 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
GLGuohu Luo
Guohu Luo
ZYZhenqiang Yao
Zhenqiang Yao
Hong ShenHong Shen
Hong Shen
This study numerically investigates the effects of an abruptly contracting and expanding annular gap on the propagation of Taylor vortices in Taylor-Couette-Poiseuille flow. The results show that the pressure drop between the inlet and the outlet exhibits oscillations with low frequency and large amplitude. The nondimensional amplitude of oscillating pressure increases linearly with an increase in the rotating Reynolds number, whereas the nondimensional oscillating frequency remains nearly invariant with varying rotating and axial Reynolds numbers. Owing to the alternate action of counter-rotating Taylor vortex pairs in front of the block, local flow resistance periodically increases and decreases, resulting in the pressure drop oscillation. By analyzing the drift velocity and wavelength of the propagating Taylor vortex pair, a prediction model for the oscillating frequency is developed. Its results show that the nondimensional frequency is proportional to the blockage ratio. With an increase in the latter, the oscillating amplitude nonmonotonically changes as a result of the tunneling phenomenon, whereby the anticlockwise rotating Taylor roller is punctured by axial flow. Based on the above mechanism of pressure oscillation, the structure of a vortex breaker is proposed that can effectively reduce the oscillation in pressure.