Bhim Prashad Kafle

Dr. Bhim Prashad Kafle


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2023 in Energies
Verified
Journal Article
Open access
PDF file
RDRajesh Dangi
Rajesh Dangi
BBBijaya Basnet
Bijaya Basnet
MPManoj Pandey
Manoj Pandey
SBSandip Bhusal
Sandip Bhusal
BBBiplab Budhathoki
Biplab Budhathoki
BKBhim Prashad Kafle
Bhim Prashad Kafle
Herein, we have prepared tin oxide (SnO2) nanoparticles (NPs), through a co-precipitation method, using SnCl2·2H2O dissolved in distilled water (DW) as a precursor. Then, the prepared NPs were heat treated in a muffle furnace, as a function of temperature, under an open atmosphere. The prepared SnO2 NPs were then re-dispersed in DW, followed by spray casting on a glass substrate, for preparing SnO2 thin films. The average thickness of the fabricated SnO2 thin films was 2.76 µm. We demonstrated a very clear variation in the structural, compositional, and morphological features of the different films (in particular, variation of the density of oxygen vacancies), which altered their electrical and optical properties. Raising the calcination temperature of the SnO2 thin films, from 250 °C to 650 °C, led to a monotonic reduction in the crystallite size, from 10.4 nm to 6.7 nm, and a decrease in the O/Sn ratio, from 5.60 to 4.79. A 14.5% decrease in the O/Sn ratio resulted in a decrease in the crystallite size by 3.7 nm (i.e., a 35.3% decrease in the NP size), and a decrease in the band gap of 0.11 eV. The lowering of the band gap, along with an increase in the oxygen vacancies in the films, accords well with previous studies. Besides, as the calcination temperature was raised, the refractive index and absorption coefficient values were also found to notably increase. Very interestingly, by simply altering the calcination temperature, we were able to produce SnO2 thin films with optical band gaps nearly equal to the fundamental band gap (2.96 eV), even though many earlier experimental studies had reported considerably greater values (3.36–4.24 eV). SnO2 thin films with lower oxygen vacancies exhibited relatively higher band gaps, which is likely to be favorable for the desired electron transport layer in perovskite solar cells.

1 July 2017 in AIP Advances
Verified
Journal Article
Open access
PDF file
MKMadhav Kafle
Madhav Kafle
RKRamesh K. Kapadi
Ramesh K. Kapadi
LJLeela Pradhan Joshi
Leela Pradhan Joshi
ARArmila Rajbhandari
Armila Rajbhandari
DSDeepak P. Subedi
Deepak P. Subedi
BKBhim Prashad Kafle
Bhim Prashad Kafle
The dependence of the structural, optical and electrical properties of the FTO thin films on the film thickness (276 nm - 546 nm), calcination environment, and low temperature plasma treatment were examined. The FTO thin films, prepared by spray pyrolysis, were calcinated under air followed by either further heat treatment under N2 gas or treatment in low temperature atmospheric plasma. The samples before and after calcination under N2, and plasma treatment will be represented by Sair, SN2 and SPl, respectively, hereafter. The thin films were characterized by measuring the XRD spectra, SEM images, optical transmittance and reflectance, and sheet resistance of the films before and after calcination in N2 environment or plasma treatment. The presence of sharp and narrow multiple peaks in XRD spectra hint us that the films were highly crystalline (polycrystalline). The samples Sair with the thickness of 471 nm showed as high as 92 % transmittance in the visible range. Moreover, from the tauc plot, the optical bandgap Eg values of the Sair found to be noticeably lower than that of the samples SN2. Very surprisingly, the electrical sheet resistance (Rsh) found to decrease following the trend as Rshair > RshN2 > RshPl. The samples exposed to plasma found to possess the lowest RshPl (for film with thickness 546 nm, the RshPl was 17 Ω/ sq.).

18 April 2016 in SOJ Materials Science & Engineering
Verified
Journal Article
Open access
BKBhim Prashad Kafle
Bhim Prashad Kafle

19 November 2020 in ACS Applied Energy Materials
Verified
Journal Article
Closed access
BKBhim Prashad Kafle
Bhim Prashad Kafle
SDSijan Devkota
Sijan Devkota
BUBibek Uprety
Bibek Uprety
KPKyun Y. Park
Kyun Y. Park
NBNiroj Basnet
Niroj Basnet
Santosh K. TiwariSantosh K. Tiwari
Santosh K. Tiwari


10 July 2017 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
BKBhim Prashad Kafle
Bhim Prashad Kafle
RLRishi Lamichhane
Rishi Lamichhane
SBSandesh Basnet
Sandesh Basnet
The optical and thermal properties of the black crome based Solar thermal collectors (STCs) deposited on three different substrates (aluminium, Al; galvanized iron, GI; and stainless steel, SS) were investigated. The devices were prepared by two different methods: electro-deposition and dip coating and were heat treated at 300 O C. Each STC's performance was evaluated by measuring optical and thermal properties: Optical properties were measured with UV-Vis, Raman and IR Spectroscopy. For later measurements, all the STC samples were kept inside an air tight glass box and are exposed to the solar radiation over all the sunshine hours in summer (from 7:30 am-5 pm, August). Then, the instantaneous temperature was recorded, simultaneously, of all samples with IR-temperature sensor. Among all the samples, the STC with black chrome coated on Al substrate showed the highest temperature, reaching the maximum value of ca. 95 O C at about 1 pm. Moreover, the STC samples fabricated by dip coating found to possess as equal optical and thermal properties as samples prepared by electro-deposition.