Yu Liu

Dr. Yu Liu


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 July 2020 in IEEE Photonics Technology Letters
Verified
Journal Article
Closed access
YLYu Liu
Yu Liu
SHShan Huang
Shan Huang
WWWenjie Wu
Wenjie Wu
PZPengfei Zhao
Pengfei Zhao
XTXuan Tang
Xuan Tang
JWJianjun Wang
Jianjun Wang
High power cladding mode stripper device has been developed in robust configurations, which demonstrated high attenuation and low temperature rise, allowing to remove 2.16 kW of power with efficiency being 21.7 dB. The maximum temperature in packaging did not exceed 55 °C at a room temperature of 20 °C. The signal insertion loss was measured to be below 0.05 dB, indicating the ability to strip the cladding light efficiently but keep the core light almost intact. A 40-min stress test has been carried out, which confirmed the working stability and reliability of the proposed cladding mode stripper. Moreover, the device presented is in a compact and closed pack, more than 2 kW of power could be completely dissipated inside a housing with merely 200 mm of length, which could not only be benefit for suppressing nonlinear effects during power delivering but also be easily integrated into high power monolithic fiber laser systems.

4 January 2022 in IEEE Photonics Journal
Verified
Journal Article
Open access
YLYu Liu
Yu Liu
SHShan Huang
Shan Huang
WWWenjie Wu
Wenjie Wu
LXLianghua Xie
Lianghua Xie
CZChun Zhang
Chun Zhang
JWJianjun Wang
Jianjun Wang
(6+1)×1 pump and signal combiner with high power handing capability, negligible beam quality degradation and bi-directional signal transmission ability has been developed by employing signal-fiber non-taper fabrication approach and in-line active splicing process. The influences of lateral core offset and angular misalignment between the signal input and output fibers in combiner have been studied theoretically, showing that M 2 factor rather than signal efficiency is more suitable to be the evaluation criterion. Three splicing methods have been compared experimentally, revealing that the M 2 -based active splicing is the most effective to preserve beam quality and obtain good efficiency simultaneously. Signal laser transmitted backward through 25-μm fiber core has shown efficiency of 95.5% and M 2 factor deterioration no more than 10% at 1 kW of power. Combined pump from laser diodes into 400-μm fiber clad has reached beyond 5 kW of power at efficiency of 98.2%, with the maximum temperature on combiner being 70.5°C, which was tested in the condition without cooling on fiber pigtails and with flat-cleaved fiber termination aggregating thermal load. Both results indicate the effectiveness of the proposed fabrication technique to make bi-directional (6+1)×1 combiner for high power and superior beam quality fiber laser systems.

8 February 2023 in Optics & Laser Technology
Verified
Journal Article
Open access
YLYu Liu
Yu Liu
WWWenjie Wu
Wenjie Wu
YLYuwei Li
Yuwei Li
YLYue Li
Yue Li
SHShan Huang
Shan Huang
JWJianjun Wang
Jianjun Wang

21 November 2023 in High Power Laser Science and Engineering
Verified
Journal Article
Open access
PDF file
YYYuefang Yan
Yuefang Yan
YLYu Liu
Yu Liu
HZHaoyu Zhang
Haoyu Zhang
YLYuwei Li
Yuwei Li
CGChao Guo
Chao Guo
rumao taorumao tao
rumao tao
All-fiber coherent beam combiners based on the self-imaging effect can achieve a near-perfect single laser beam, which can provide a promising way to overcome the power limitation of a single-fiber laser. One of the key points is combining efficiency, which is determined by various mismatches during fabrication. A theoretical model has been built, and the mismatch error is analyzed numerically for the first time. The mismatch errors have been numerically studied with the beam quality and combining efficiency being chosen as the evaluation criteria. The tolerance of each mismatch error for causing 1% loss is calculated to guide the design of the beam combiners. The simulation results are consistent with the experimental results, which show that the mismatch error of the square-core fiber is the main cause of the efficiency loss. The results can provide useful guidance for the fabrication of all-fiber coherent beam combiners.

4 April 2023 in Optics & Laser Technology
Verified
Journal Article
Open access
YLYuwei Li
Yuwei Li
YLYu Liu
Yu Liu
FLFengyun Li
Fengyun Li
NLNian Liu
Nian Liu
YLYue Li
Yue Li
FJFeng Jing
Feng Jing

15 December 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
YLYu Liu
Yu Liu
WWWenjie Wu
Wenjie Wu
PZPengfei Zhao
Pengfei Zhao
SHShan Huang
Shan Huang
YLYuwei Li
Yuwei Li
JWJianjun Wang
Jianjun Wang
A design integrating multiple cladding mode strippers used in fiber laser architectures into a single device is proposed. This approach can increase the compactness of fiber lasers, thus contributing to industrial laser processing applications. By offset-placing the most intense light-stripping parts, for instance, by inversing the laser injection directions or by displacing the beginning of etched sections, multiple cladding mode strippers bundled together into a single housing can have the hottest regions separated and can operate at full power simultaneously, with no evident cross-influence on each other. Two and three cladding-mode-stripper arrays have been implemented, and validation tests have been conducted with ~500-W cladding power being injected into each input port. For both arrayed devices, compared to the scenario in which only a single cladding mode stripper is working, no greater than a 2.1 °C temperature increment is generated when all components are operating concurrently, which demonstrates the effectiveness of the integration method. In this way, one half and two thirds of space/weight reduction can be realized, respectively, for the two and three cladding-mode-stripper arrays, which is meaningful, since cladding mode strippers are among the most bulky and hottest components in fiber lasers. Moreover, this integration provides a valuable reference for the miniaturization of other components, and thus, could contribute to the development fiber lasers with higher power-to-volume ratios, which would be more economical for industrial applications.