In this work, mode evolution in the presence of stimulated Raman scattering (SRS) effect has been studied in a 2 kW polarization-maintained (PM) fiber amplifier. It proved that the SRS-induced mode distortion can be observed at 40 dB of signal to Raman noise ratio in a PM fiber amplifier, which is significantly lower than that in a non-PM system. By using mode decomposition (MD) method, the SRS-induced mode distortion has been analyzed quantitatively by decomposing the signal and the Raman light individually, and the signal mode evolution shows a dissimilar phenomenon compared with the SRS-induced transverse mode instability. The SRS effect in large mode area fiber lasers result in continuous excitation of signal high order modes (HOMs), which leads to the signal beam quality deterioration and the output power rollover. The power fraction of HOMs increases by 30% with the Raman power ratio only being 1.67% at the maximal output power, and the Raman Stokes light mainly exists in fundamental mode distribution, which can be attributed to the beam cleanup effect.
(6+1)×1 pump and signal combiner with high power handing capability, negligible beam quality degradation and bi-directional signal transmission ability has been developed by employing signal-fiber non-taper fabrication approach and in-line active splicing process. The influences of lateral core offset and angular misalignment between the signal input and output fibers in combiner have been studied theoretically, showing that M 2 factor rather than signal efficiency is more suitable to be the evaluation criterion. Three splicing methods have been compared experimentally, revealing that the M 2 -based active splicing is the most effective to preserve beam quality and obtain good efficiency simultaneously. Signal laser transmitted backward through 25-μm fiber core has shown efficiency of 95.5% and M 2 factor deterioration no more than 10% at 1 kW of power. Combined pump from laser diodes into 400-μm fiber clad has reached beyond 5 kW of power at efficiency of 98.2%, with the maximum temperature on combiner being 70.5°C, which was tested in the condition without cooling on fiber pigtails and with flat-cleaved fiber termination aggregating thermal load. Both results indicate the effectiveness of the proposed fabrication technique to make bi-directional (6+1)×1 combiner for high power and superior beam quality fiber laser systems.
19 October 2022 in Journal of Lightwave Technology
By employing the mode decomposition method to study the relative mode evolution characteristics during the stimulated Raman scattering (SRS) process, a numerical model of the core-pumped Raman effect in few-mode fibers has been proposed, which provides an accurate tool to reveal the underlying physical mechanism of SRS-induced mode distortion. Mode distortion induced by the SRS effect in large-mode area passive fibers has been investigated numerically. It reveals that the few-mode SRS effect can result in an irreversible power transfer from the signal fundamental mode (FM) to signal high order modes (HOMs), which is a static phenomenon, different from the SRS-induced transverse mode instability. To the best of our knowledge, it is the first time that the numerical results coincide with the experimental phenomenon. Simulation results also illustrate that the inter-mode wave-mixing effect among the signal FM and signal HOMs plays a key role in the signal power transfer. With the help of the numerical model, mitigation strategy by designing and using the Raman-gain-tailored fiber has also been proposed, which shows a clear advantage in suppressing SRS-induced mode distortion.
The spatial-spectral evolution properties of laser beam in the presence of stimulated Raman scattering (SRS) effect have been studied in large mode area (LMA) fiber. With the employment of long/short pass filters, spatial evolution of the signal and Raman light has been studied individually. After the onset of SRS, the simultaneous optimizing of signal light and degrading of Raman light was observed, which has been attributed to the SRS effect of multimode laser beams in LMA fiber. The spectral evolution characteristics indicated that the SRS effect in LMA fiber will trigger other nonlinear effects, mainly inter-modal four-wave-mixing effect and cross-phase-modulation induced modulation instability. Furthermore, the impacts of bending strategy and multimode LMA fiber on SRS-induced spatial-spectral distortion have also been studied, which shows that the SRS-induced mode distortion can be suppressed by increasing the fiber size while the bending strategy plays a limited role.
A high-power, narrow-linewidth, all-fiber polarization-maintaining (PM) amplifier has been demonstrated. A lasing power of 5870 W has been delivered in master oscillator power amplifier architecture with cascaded white noise source (WNS) phase modulation and bidirectional pumping schemes. The maximal power was limited by the onset of stimulated Brillouin scattering. At the maximum power operation, the amplifier exhibited a 3 dB spectral linewidth of 0.43 nm with beam quality being M2 < 1.33 and polarization extinction ratio (PER) being 16.3 dB. To the best of our knowledge, this represents the highest spectral brightness and PER achieved by PM fiber laser systems around 6 kW-level operation.
About Me
major in high power fiber laser systems, especially nonlinear effects and mode-related area.
major in high power fiber laser systems, especially nonlinear effects and mode-related area.