Magnetorheological/electrorheological dampers are complex devices and involve a large set of important material and geometric variable with mutual interactions between them. As such, reliable predictions of the damping force level in these devices are difficult to achieve. However, meaningful results can be obtained with significantly less effort through nondimensional parameters involving all key variables. Therefore, the goal of this study was to propose a robust set of nondimensional parameters for the purpose of modeling of magnetorheological/electrorheological dampers (and other flow-mode devices) as well as the characterization of data from experiments with magnetorheological/electrorheological devices. The proposed scheme employs five parameters characterizing the contribution of flow inertia, viscosity, and yield stress, as well as shear thinning/thickening effects to the damping force output of magnetorheological/electrorheological valves. It is the result of analysis of several constitutive models of non-Newtonian fluid models (Bingham plastic model, biviscous model, biplastic Bingham model, and Herschel–Bulkley model). Specifically, the goal was to derive analytical (exact) formulae for pressure gradient of all examined models excluding the Herschel–Bulkley model. In the Herschel–Bulkley model, the nondimensional relationship between pressure gradient and flow rate is given in a power-law form, and the analytical (exact) solution cannot be obtained. Prior art included analytical (exact) solutions for the Bingham plastic model only. In the most generic form, the expressions can be useful for designing magnetorheological/electrorheological flow-mode devices. Exemplary calculations of the damping force output are presented in this article for a custom single-gap magnetorheological piston. The piston contains a semi-bypass feature in the annulus to allow for low-breakaway forces at near-zero piston velocity inputs. The steady-state calculations are presented for two exemplary damper units, and the model is validated against experimental data. Finally, the expressions allow one to easily characterize flow data into separate regimes of damper operation by means of the proposed scheme.
The study deals with the pinch mode of magnetorheological (MR) fluids’ operation and its application in MR valves. By applying the principle in MR valves a highly non-uniform magnetic field can be generated in flow channels in such a way to solidify the portion of the material that is the nearest to the flow channel’s walls. This is in contrary to well-known MR flow mode valves. The authors investigate a basic pinch mode valve in several fundamental configurations, and then examine their magnetic circuits through magnetostatic finite-element (FE) analysis. Flux density contour maps are revealed and basic performance figures calculated and analysed. The FE analysis results yield confidence in that the performance of MR pinch mode devices can be effectively controlled through electromagnetic means.
15 December 2011 in Journal of Vibration and Control
Controllable dampers based on smart fluids contain internal passages through which the working fluid flows and wherein the controlled pressure drop occurs under the influence of magnetic or electric fields. In this paper, the dynamics of such dampers are analysed through a series of theoretical dynamic models of increasing detail and complexity. The models capture the medium- and high-frequency dynamics of the damping force output of the damper and include the lumped mass of the fluid contained in the internal flow passages, the piston and rod assembly mass, and the compressibility of the fluid and pressurized gas contained within the chambers of the damper. The models are derived in state-space form from which transfer functions and natural frequencies are obtained analytically and then calculated for each of the systems. The results are presented in the form of frequency responses (Bode plots). Finally, the effects of the key geometric parameters of the damper and of the relevant fluid properties on the damper force output dynamics are presented and discussed.
This study concerns the modeling of the hysteretic behavior of magnetorheological (MR) dampers. In general, hysteresis is one of key factors influencing the output of such actuators. So far, more attention has been paid to studying the combined hysteretic behavior of MR actuators by observing the relationships between the output (force/torque) and the inputs (current, velocity, and position). However, these devices feature two distinct hysteretic mechanisms: mechanical/hydraulic and magnetic. The mechanical hysteresis is of different nature than the magnetic hysteresis due to the properties of ferromagnetic materials forming the actuator's electromagnet circuit, and these should be split in the modeling process. In the present study, we separate the magnetic hysteresis from the mechanical/hydraulic one by investigating the magnetic flux vs. exciting current relationship of a commercial flow-mode MR damper subjected to sinusoidal current loading and independently of the mechanical excitations. The resulting behavior of the electromagnetic circuit is then examined using the non-linear inductor approach with hysteresis. Total hysteresis is then modeled using a non-linear inductor model in combination with a phenomenological parametric Maxwell type model of the damper.
Magnetorheological (MR) fluids are suspensions of fine, low-coercivity, high-magnetizable particles in a continuous liquid phase. When subjected to magnetic field, the material exhibits a rapid change in the apparent viscosity of several orders of magnitude. This unique capability has been successfully exploited in automotive semi-active suspensions systems or systems for manufacturing high quality optics. In a majority of the existing systems, the rheology of MR fluids is controlled by an external uniform field oriented perpendicularly to the fluid flow direction. In general, it is an inherent feature of MR systems operating in flow, shear or squeeze modes, respectively. There is an experimental evidence that the behavior of MR fluids in the so-called pinch-mode (in which the fluid is subjected to non-uniform magnetic field distributions) clearly stands out against the remaining three operating modes. With the predecessors, the flow through the channel occurs once a pressure across it exceeds the field-dependent threshold pressure. For comparison, in pinch mode valves the magnetic flux energizes mostly the layers of the materials near the channel walls. The outcome is a change in the channel’s effective diameter achieved solely via material means without changing its geometry. To study the fluid’s unique behaviour in the pinch mode, the authors designed a prototype valve assembly and examined several fluid formulations of various particle concentration levels across a wide range of external (velocity, magnetic field density) stimuli in an organized effort to further comprehend the phenomenon. The obtained data indicate that the magnitude of the particular effect does not only depend on the magnitudes of the magnetic stimuli but also on the particle concentration; the smaller the concentration of particles the more pronounced the pinch mode like behavior is. In general, the authors believe that the study may provide guidelines as to the selection of fluid formulations for developing novel valveless actuators utilizing MR fluids operating in pinch mode.
Hysteresis is one of key factors influencing the output of magnetorheological (MR) actuators. The actuators reveal two primary sources of hysteresis. The hydro(mechanical) hysteresis can be related to flow dynamics mechanisms and is frequency‐ or rate‐dependent. For comparison, the magnetic hysteresis is an inherent property of ferromagnetic materials forming the magnetic circuit of the actuators. The need for a good quality hysteresis model has been early recognized in studies on MR actuators; however, few studies have provided models which could be used in the design stage. In the paper we reveal a hybrid multiphysics model of a flow‐mode MR actuator which could be used for that purpose. The model relies on the information which can be extracted primarily from material datasheets and engineering drawings. We reveal key details of the model and then verify it against measured data. Finally, we employ it in a parameter sensitivity study to examine the influence of magnetic hysteresis and other relevant factors on the output of the actuator.