Tobias Pascal Willian

Mr. Tobias Pascal Willian

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
TWTobias Pascal Willian
Tobias Pascal Willian
BFBettina Fasolt
Bettina Fasolt
Paul MotzkiPaul Motzki
Paul Motzki
Gianluca RizzelloGianluca Rizzello
Gianluca Rizzello
Stefan SeeleckeStefan Seelecke
Stefan Seelecke
Dielectric elastomer (DE) transducers possess various advantages in comparison to alternative actuator technologies, such as, e.g., electromagnetic drive systems. DE can achieve large deformations, high driving frequencies, and are energy efficient. DEs consist of a dielectric membrane sandwiched between conductive electrodes. Electrodes are especially important for performance, as they must maintain high electrical conductivity while being subjected to large stretches. Low electrical resistances allow faster actuation frequencies. Additionally, a rate-independent, monotonic, and hysteresis-free resistance behavior over large elongations enables DEs to be used as resistive deformation sensors, in contrast to the conventional capacitive ones. This paper presents a systematic study on various electrode compositions consisting of different polydimethylsiloxane (PDMS) and nano-scaled carbon blacks (CB). The experiments show that the electrode resistance depends on the weight ratio of CB to PDMS, and the type of CB used. At low ratios, a high electrical resistance accompanied by a bimodal behavior in the resistance time evolution was observed, when stretching the electrodes cyclic in a triangular manner. This phenomenon decreases with increasing CB ratio. The type of PDMS also influences the resistance characteristics during elongation. Finally, a physical model of the observed phenomenon is presented.

17 April 2024 in Advanced Engineering Materials
Verified
Journal Article
Open access
TWTobias Pascal Willian
Tobias Pascal Willian
SPSvenja Pohl
Svenja Pohl
DBDaniel Bruch
Daniel Bruch
Gianluca RizzelloGianluca Rizzello
Gianluca Rizzello
Paul MotzkiPaul Motzki
Paul Motzki
Stefan SeeleckeStefan Seelecke
Stefan Seelecke
Dielectric elastomer transducers (DETs), namely, highly stretchable dielectric membranes sandwiched between two compliant electrodes, allow to develop sensors, actuators, and generator systems. DET performance is strongly influenced by the material properties of dielectric and electrodes, as well as the type of manufacturing process. For instance, when manufacturing the electrodes via screen‐printing, significant amounts of solvents are needed to adjust the printing materials’ viscosity, but they potentially alter DET properties. The investigation of this effect, however, is largely unexplored. Addressing this issue, this article investigates the influence of various solvents on a DET consisting of a polydimethylsiloxane (PDMS) membrane with PDMS/carbon black electrodes. Physical and chemical interactions between dielectric and solvents are characterized by infrared‐spectroscopy (IR), optical investigations, and light microscopy. Different solvents used for screen‐printing are analyzed in terms of their effects on the electrode electrical resistance, screen‐print image, and breakdown strength. Even though the solvent strongly affects the electrodes’ electrical resistance (ranging from ≈22 kΩ to >MΩ), it does not modify the breakdown strength of the pure dielectric (113 V μm−1). In the IR, no chemical aging is found. The obtained results provide systematic guidelines for the choice of solvents in DET electrode manufacturing.

14 June 2022 in Actuators
Verified
Journal Article
Open access
PDF file
DBDaniel Bruch
Daniel Bruch
TWTobias Pascal Willian
Tobias Pascal Willian
HSHendrik Cornelius Schäfer
Hendrik Cornelius Schäfer
Paul MotzkiPaul Motzki
Paul Motzki
Thanks to their outstanding properties, in the last few years Dielectric Elastomer Actuators (DEAs) have increasingly attracted the interest of the scientific community and generated a surge in the effort devoted to their industrialization. Compared to conventional actuator systems, DEAs are based on inexpensive and widely available polymeric materials, which make them potentially attractive from a market perspective. However, DEA systems with a given layout and dimensions have a fixed force-stroke response that is only suitable for a specific load profile. This leads to a wide variety of designs combined with small production volumes and high costs, limiting the competitive advantage. This work addresses this issue by proposing a combination of DEA systems with compliant scissor linkage transmission mechanisms, which provide linear stroke and force scaling and simultaneously maintain performance optimization by leaving the convertible energy density of the DEA unaffected. For this purpose, three systems are designed, based on a same strip-shaped DEA combined with inclined buckled beam biasing mechanisms. Two of the systems are coupled with scissor linkages that offer transmission ratios of 3:1 and 1:3, respectively, to adapt the system to different load profiles. The system design is explained in detail, and the functional principle is validated through experiments.

28 June 2026 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
TWTobias Pascal Willian
Tobias Pascal Willian
DBDaniel Bruch
Daniel Bruch
PMPaul Motzki
Paul Motzki
SSStefan Seelecke
Stefan Seelecke
Dielectric elastomer transducers (DETs) are used in various applications, ranging from actuators to sensors and generators. For optimal performance, homogeneous electrical charging characteristics, which depend on the current flow distribution over the electrode area, are indispensable. To enable the investigation of such current flow distributions, a novel approach using thermal imaging (TI) is presented in this paper. The approach uses high-frequency voltage excitation to induce resistive heating in the DET electrodes and generates temperature maps to visualize the current flow, thus providing insight into the local charging behavior. This way, the effects of electrode geometry, electrical contact layout as well as potential manufacturing-related imperfections can be studied. The paper starts by introducing an experimental setup and the effect of excitation parameters. It subsequently illustrates the method using 50 µm strip-shaped silicone films with different screen-printed carbon black/PDMS electrodes, also taking the effect of mechanical strains into account. The results allow for an interpretation of the effectiveness of electrode design, motivate potential future quality tests and may serve as a validation method for, for example, multi-physics finite element simulation tools.