Water-based enhanced oil recovery methods have been developed to improve the oil production rate from ultra-tight reservoirs. By coupling the effect of surfactant as wettability alteration and water alternating gas injection method, we aimed to determine the most efficient enhanced oil recovery technique. We performed seven injectivity scenarios to measure the oil recovery factor by introducing the alkylbenzene sulfonic acid (LABSA) as a surfactant agent during the active carbonated water alternating gas (ACWAG) injection. To consider the effect of slug size during water alternating gas injection, we used two different slug sizes (0.3, and 0.6). After the water breakthrough, a little oil volume was produced, and the maximum oil recovery factor at 1.5 Pore Volume (PV) was 26%. This issue corresponded to the water channeling after the breakthrough point. For smaller slug sizes (0.3), the maximum oil recovery factor (78%) was reached in smaller pore volumes. One of the exciting results wass the considerable influence of slug ratio during the water alternating gas (WAG) injection, in which it provided more oil recovery factor (83%) when the gas volume is higher than the water volume. Finally, by introducing the coupling effect of active carbonated water (made by LABSA surfactant) and WAG injection, the maximum oil recovery factor was 85%, corresponding to the better efficiency of active carbonated water in interfacial tension reduction. The results of this comprehensive investigation can be extended in ultra-tight sandstone reservoirs and can be applied as a further guideline in numerical simulations. Graphical abstract
9 March 2026 in Journal of Petroleum Exploration and Production Technology
Improving oil recovery from ultra-tight reservoirs remains a critical challenge due to their inherently low permeability, restricted pore connectivity, and poor sweep efficiency. This study presents a systematic experimental investigation of water-based enhanced oil recovery (EOR) techniques applied to core samples from the Tarim Basin. Coreflooding tests were conducted using conventional methods (waterflooding, CO₂ injection), hybrid strategies including Water Alternating Gas (WAG), Gas Alternating Water (GAW), and Alkali–Surfactant–Polymer (ASP), and advanced chemical-assisted schemes, including four Carbonated Water Alternating Gas (CWAG) variants and a novel Active Carbonated Water Alternating Gas (ACWAG) method. Results showed that ACWAG achieved the highest oil recovery (85.3%) and the lowest residual oil saturation (15.7%), outperforming all other techniques. Key performance indicators such as pressure behavior, wettability alteration, and slug size sensitivity confirmed the importance of injection sequencing and chemical formulation. This study provides new insights into the design of EOR strategies for ultra-tight formations and introduces a promising hybrid approach that could be scaled for field application.
In this study, we experimentally investigated the effects of chemically enhanced oil recovery methods containing hydrolyzed polyacrylamide (HPAM), surfactant–hydrolyzed polyacrylamide (SHPAM), surfactant nanofluids (SNF), that is, coupled with carbon dioxide (CO2) and water chase injection to measure enhanced oil recovery methods in a sandstone reservoir. To proceed with the experiments, we performed four flooding tests at the simulated reservoir temperature of 70 °C. The sand packs were saturated with oil to establish the irreducible water saturation (Swr). Then, the fluid flow in sand packs remained undistributed for about 5 days to obtain the 1.5 pore volume (PV). We observed that the pressure drop had small fluctuations when there was waterflooding (until 1.5 PV), and after injecting the chemical agents, the pressure drop had a sharp rise. It is indicated that the chemical solution has implemented higher pressure drops (significant energy efficiency) to displace the oil instead of water. The maximum oil recovery factor was about 53% and 59% when HPAM and SHPAM solution displaced oil after waterflooding, respectively; however, it is observed that water chase flooding recovered about 8% and 14% of remaining oil in place while CO2 has increased only 3% and 5%, respectively. SNF solution can provide more oil recovery factors. It is about 72% (SNF with 0.5 wt%) and 67% (SNF with 1 wt%). We observed that water chase flooding recovered about 20% of oil in place while CO2 increased by only 8%. It was concluded that the SNF solution with 0.5 wt% tends to adhere to the water–CO2 and causes to improve oil recovery factor after SNF injection. Therefore, SNF is the optimum enhanced oil recovery method among other chemical agents. On the other hand, with the decrease in CO2 flow rate and increase in silica nanoparticles slug size, pressure drop has started to decrease in higher pore volume injections, indicating that larger volumes of CO2 can be stored in sand packs. However, by increasing the CO2 flow rate and decreasing silica nanoparticles slug size, CO2 can escape easily from the sand pack.
1 February 2015 in Chinese Journal of Applied and Environmental Biology