In this study, chromate adsorption onto red peanut skin (RPS) was investigated in a fixed-bed column; FTIR, PZC, SEM, DLS, and BET were used to evaluate its adsorption properties. The experiments were conducted to determine the effect of physical parameters, including the inlet initial Cr(VI) concentration (100–500 mg L−1), bed height (10–20 cm), and feed flow rate (13.59–23.45 mL min−1). They were carried out to predict breakthrough curves. The adsorption capacity coefficients were determined using the most widely used Bohart–Adams model. It was tested to fit experimental data, for a better understand the dynamic behavior, and for further optimize column performance. It was found that the Cr(VI) uptake decreases when increasing the flow rate and that high chromate concentration and bed height consequently increase the column’s life span. A high column adsorption capacity can be achieved with a higher Cr(VI) concentration due to the higher driving force. The results indicated that the Bohart–Adams model provides a good description (R2 > 0.98) of the experimental data of the Cr(VI)’s removal from the aqueous solution on the RPS suggesting that the surface diffusion is the rate-limiting step in the continues adsorption process.. Breakthrough adsorption capacity is crucial for comparing RPS with other similar materials. Indeed, possible mechanisms have been suggested for illustrating adsorption onto RPS. The obtained results showed significant potential of 26.23 mg g−1 of RPS on Cr(VI) elimination at a natural pH of 5.35. Furthermore, this global investigation allowed for the design of a promising low-cost material for the future scale-up of cleaning wastewater polluted by metal and determine the properly conditions for operating column adsorption. This material provides an economical, efficient means of eliminating pollutants, thus meeting the main aims of the UN Sustainable Development Goals (UN SDGs).
13 November 2022 in Research on Chemical Intermediates
In this study, the solar photo-Fenton (SPF) process was investigated for the degradation of doxycycline (DOX) using a solar compound parabolic collector (CPC) reactor and a borosilicate serpentine tube with an irradiated volume of 1.8 L. The influence of the operating parameters, such as H2O2, Fe2+ dosage, and DOX concentration, was investigated. The optimum H2O2, Fe2+ dosage, and DOX concentration were found to be 4, 0.1, and 0.06 mM, respectively. The results of photo-Fenton experiments fitted the pseudo-first-order kinetic equation (R2 = 0.99). The efficiency of the treatment under optimized conditions was analyzed by an HPLC analysis of the samples, chemical oxygen demand (COD), and total organic carbon (TOC). The results obtained showed that the solar photo-Fenton process achieved a DOX degradation of 95.07%, a COD elimination of 81.43%, and a TOC elimination of 73.05%. The phytotoxicity tests revealed a 73.32% decrease in the germination index of watercress seeds, demonstrating that the SPF process minimizes the toxicity of the chemical and did not have any negative impact on plant growth. Overall, the results of this study suggest that SPF is a promising technology for the removal of doxycycline from wastewater.
The adsorption of oxytetracycline from aqueous solution by the resin Amberlite IR 120 was studied. The effect of different experimental parameters such as contact time, initial concentration of OTC 40-200 mg/l, initial pH 2-12 of aqueous solution, adsorbent dose 0.5-3 g/l, and stirring speed 100-700 rpm on the adsorption of OTC were investigated. The kinetic adsorption experimental results were analyzed using pseudo-first order, pseudo-second order and Elovich kinetic models. The adsorption process was found to follow a pseudo-second order kinetic model and the corresponding rate constants were obtained. A film-pore diffusion (FPD) mass transfer model has been developed to predict the concentration distribution in the fluid phase, based on the external mass transfer coefficient and the effective diffusion coefficient. The values of the external mass transfer coefficient (beta(L)) and effective diffusion coefficient (D-eff) were found to decrease with increasing OTC concentration. The comparison between the experimental and the theoretical curves allowed us to note that the film-pore diffusion mass transfer model gave a good agreement with the experimental data for all the values of initial OTC concentration.