Muhammad Wahab

Prof. Muhammad Wahab


Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 July 2016 in Acta Metallurgica Sinica (English Letters)
Verified
Journal Article
Closed access
PDF file
SASaad B. Aziz
Saad B. Aziz
MDMohammad W. Dewan
Mohammad W. Dewan
DHDaniel J. Huggett
Daniel J. Huggett
MWMuhammad Wahab
Muhammad Wahab
Ayman OkeilAyman Okeil
Ayman Okeil
TLT. Warren Liao
T. Warren Liao

4 October 2017 in Acta Metallurgica Sinica (English Letters)
Verified
Journal Article
Closed access
PDF file
SASaad B. Aziz
Saad B. Aziz
MDMohammad W. Dewan
Mohammad W. Dewan
DHDaniel J. Huggett
Daniel J. Huggett
MWMuhammad Wahab
Muhammad Wahab
Ayman OkeilAyman Okeil
Ayman Okeil
TLT. Warren Liao
T. Warren Liao

4 April 2016 in Research in Nondestructive Evaluation
Verified
Journal Article
Closed access
DHD. J. Huggett
D. J. Huggett
MDM. W. Dewan
M. W. Dewan
MWMuhammad Wahab
Muhammad Wahab
Ayman OkeilAyman Okeil
Ayman Okeil
TLT. W. Liao
T. W. Liao
Nondestructive evaluation (NDE) techniques of phased array ultrasonic testing (PAUT) and digital X-ray radiography were employed on friction stir (FS)-welded Aluminum Alloy (AA)-2219-T87 specimens. PAUT intricacies required for scanning of FS-welded specimens with a 10-MHz 32-element transducer are discussed. The time corrected gain (TCG) calibration is required for scanning with an increase in index offset to compensate for decrease in A-Scan signal peak amplitude. Calibration techniques to find small defects with appropriate size tolerances are also established. The NDE technique of digital X-ray radiography is compared to PAUT, where it was found that a calibrated PAUT system is able to discover defects less than 0.2 mm where X-ray radiography could not. Incomplete penetration (IP), wormhole (WH), surface cavity (SC), and internal void (IV) defects are analyzed. Furthermore, an online PAUT system for FSW has been developed and successfully tested. The work provided herein will provide a gateway for an ultimate goal of an automated PAUT online sensing system.

17 November 2017 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
DHD. J. Huggett
D. J. Huggett
TLT. W. Liao
T. W. Liao
MWMuhammad Wahab
Muhammad Wahab
Ayman OkeilAyman Okeil
Ayman Okeil

4 September 2015 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
MDMohammad W. Dewan
Mohammad W. Dewan
MWMuhammad Wahab
Muhammad Wahab
Ayman OkeilAyman Okeil
Ayman Okeil
Welding defects and the reduction of mechanical performances are the foremost problems for fusion welded aluminum alloys joints. The influences of weld defects and postweld heat treatment (PWHT) on tensile properties of gas tungsten arc (GTA) welded aluminum alloy AA-6061-T651 joints are investigated in this current study. All welded specimens are nondestructively inspected with phased array ultrasonic testing (PAUT) to classify weld defect and measure the projected defects area-ratio (AR). Ultimate tensile strength (UTS) decreased linearly with the increase of the size of weld defect but tensile toughness behaved nonlinearly with defect size. Depending on defect size, defective samples' joint efficiency (JE) varied from 35% to 48% of base metal's (BM) UTS. Defect-free as-welded (AW) specimens observed to have 53% and 34% JE based on UTS and yield strength (YS) of BM, respectively. PWHT was applied on defect-free welded specimens to improve tensile properties by precipitation hardening, microstructures refining, and removal of postweld residual stresses. Solution treatment (ST) (at 540 °C) followed by varying levels of artificial age-hardening (AH) time was investigated to obtain optimum tensile properties. For GTA-welded AA-6061-T651, peak aging time was 5 hr at 180 °C. PWHT specimens showed 85% JE based on UTS and up to a 71% JE based on YS of BM. However, toughness values decreased about 29% due to the presence of precipitate-free fusion zones. The experimental investigations can be used to establish weld acceptance/rejection criteria and for the design of welded aluminum alloy structures.

15 February 2011 in Materials Letters
Verified
Journal Article
Closed access
JLJ. Liang
J. Liang
KWK.Y. Wang
K.Y. Wang
SGShengmin Guo
Shengmin Guo
MWMuhammad Wahab
Muhammad Wahab