Seyit Mehmet DEMET

Dr. Seyit Mehmet DEMET

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2023 in Polymer Composites
Verified
Journal Article
Open access
HSHarun Sepetcioglu
Harun Sepetcioglu
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
MBMehmet Bagci
Mehmet Bagci
Basalt fiber reinforced polymer (BFRP) composite pipe is an excellent alternative to glass and carbon fiber reinforced composite pipes in industry and promising in high recycling for polymer composite used in aerospace, marine, and automotive. To enhance the solid particle erosion (SPE) properties of filament‐wound BFRP composite pipe while preserving its mechanical properties, reinforced BFRP composite pipes were prepared to employ non‐functionalized graphene nanoplatelets (GnPs) at a reinforcement concentration of 0.25 wt.% and ultrasonication mixing technique. The SPE behavior of GnPs reinforced and non‐reinforced BFRP composite pipes were characterized by axial and radial positioning of the inner and outer surfaces of the pipes. In each case, the erosion rates of these composite pipes were evaluated at five impingement angles (30°, 45°, 60°, 75°, and 90°) and an impact velocity of 34 m/s. The erosion response of both BFRP composite pipes' outer surfaces showed a semi‐ductile in the axial positioning, with a maximum erosion rate at a 60° impingement angle. However, these composite pipes' inner surfaces in the same positioning presented a maximum erosion rate at a 45° impingement angle. Besides, it is explored that the GnPs contribute to an improvement of approximately 10%–55% in erosive wear resistance of the non‐reinforced BFRP composite pipes. The damage analysis of eroded surfaces was examined through scanning electron microscopy (SEM), and the GnPs effect upon composite pipes' erosion micromechanisms was presented and discussed in detail.Highlights: GnPs increased the BFRP composite pipe's erosion resistance. Erosion rate on the inner surface increases due to particle accumulation. GnPs improved erosion behavior via solid lubrication and mechanical properties.

8 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
HSHarun Sepetcioglu
Harun Sepetcioglu
MBMehmet Bagci
Mehmet Bagci
Basalt/epoxy composite pipes in a [±55]4 winding configuration were produced on CNC filament winding machines (10 N fiber tension and ~11 mm bandwidth). In the experiments, a 34 m/s impact velocity was set using the double-disc method, and five different particle impingement angles (30, 45, 60, 75, and 90°) were used to determine the erosive effect on the outer surfaces of filament wound composite pipes under the influence of 600 μm erodent particles with angular geometry in the test set, complying with the ASTM G76-95 standard. The winding patterns in the lamina (±55 angle-ply laminate region) and zigzag (±55 zigzag region) regions of BFR/EP pipes were determined to have significant effects on solid particle erosion resistance, as evidenced by the SEM images.

21 May 2025 in Polymer Composites
Verified
Journal Article
Open access
HSHarun Sepetcioglu
Harun Sepetcioglu
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
İdris KARAGÖZİdris KARAGÖZ
İdris KARAGÖZ
MBMehmet Bagci
Mehmet Bagci
The aim of this study is to investigate the solid particle erosion behavior of walnut shell (WS)‐filled acrylic‐styrene‐acrylate (ASA) and polycarbonate/acrylic‐styrene‐acrylate (PC/ASA) thermoplastic blend composites under various erosion conditions. Erosion resistance tests were conducted using Al 2 O 3 particles (600 μm, Mohs hardness 9) as erodent, at a velocity of 34 m/s, with impingement angles ranging from 30° to 90°. Test samples were subjected to these conditions for 24 s, and weight loss was measured to determine erosion rates. Key parameters such as density, hardness, and erosion coefficients were also evaluated. Composites with 10 wt% WS filler exhibited optimal performance, reducing erosion rates by up to 36.7% compared to unfilled PC/ASA blend. Macro and SEM imaging revealed the damage mechanisms, showing less material loss and better surface durability in WS‐filled composites. This study demonstrates that incorporating WS into ASA and PC/ASA matrices not only improves erosion resistance but also aligns with the goal of sustainable material development. The results suggest that these composites could be highly effective in industries where materials are exposed to wear and tear from abrasive forces, such as in construction or automotive applications.

17 September 2025 in International Journal of Pressure Vessels and Piping
Verified
Journal Article
Closed access
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
YKYusuf Kepir
Yusuf Kepir
AGAlper Gunoz
Alper Gunoz
HSHarun Sepetcioglu
Harun Sepetcioglu
MBMehmet Bagci
Mehmet Bagci
MKMemduh Kara
Memduh Kara

28 June 2021 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Verified
Journal Article
Closed access
PDF file
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
AEAli S Ersoyoğlu
Ali S Ersoyoğlu
In this study, the fatigue performances of symmetrical and asymmetrical spur gears were analyzed by performing single tooth bending fatigue tests. The gears tested were determined to be symmetrical spur gears with a 20°/20° pressure angle, asymmetrical spur gears with a 20°/22° pressure angle, and asymmetrical spur gears with a 20°/25° pressure angle. These gears were made of AISI 4140 material. Single tooth bending fatigue tests were performed under variable loads. Considering the tests performed at the same torque values in asymmetrical spur gears with a 20°/22° pressure angle compared to symmetrical spur gears with a 20°/20° pressure angle, a statistically significant increase in performance was achieved at close to 90%. While gears with 20°/20° and 20°/22° pressure angles break at the tooth root, tooth flank fracture was observed in relatively high numbers of cycles in asymmetric spur gears with a 20°/25° pressure angle. It was observed that the formation of tooth flank damage negatively affected the fatigue performance.

28 July 2014 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
HIH Imrek
H Imrek
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
Due to their superior features, such as low coefficients of friction, resistance against chemical effects, and good strength-to-weight ratio, polymer-based composite bearings are widely used in industries. Polymer composite bearing calculations are made based on experimental study data. In this study, experimental investigations were conducted on polytetrafluoroethylene composite radial bearings reinforced with 35% carbon and 40% bronze material where bearing loads, sliding distances, and wear were taken into consideration. The results for both materials are given graphically and compared with each other. In accordance with the results, it was considered that polytetrafluoroethylene/bronze composite film thickness and film composition on the surfaces extensively affect wear rate. It was found that these films' thicknesses depends on adhesion between steel and composite surfaces, cohesive properties of composite, load, and sliding distance.