Mehmet Bagci

Prof. Dr. Mehmet Bagci

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2023 in Polymer Composites
Verified
Journal Article
Open access
HSHarun Sepetcioglu
Harun Sepetcioglu
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
MBMehmet Bagci
Mehmet Bagci
Basalt fiber reinforced polymer (BFRP) composite pipe is an excellent alternative to glass and carbon fiber reinforced composite pipes in industry and promising in high recycling for polymer composite used in aerospace, marine, and automotive. To enhance the solid particle erosion (SPE) properties of filament‐wound BFRP composite pipe while preserving its mechanical properties, reinforced BFRP composite pipes were prepared to employ non‐functionalized graphene nanoplatelets (GnPs) at a reinforcement concentration of 0.25 wt.% and ultrasonication mixing technique. The SPE behavior of GnPs reinforced and non‐reinforced BFRP composite pipes were characterized by axial and radial positioning of the inner and outer surfaces of the pipes. In each case, the erosion rates of these composite pipes were evaluated at five impingement angles (30°, 45°, 60°, 75°, and 90°) and an impact velocity of 34 m/s. The erosion response of both BFRP composite pipes' outer surfaces showed a semi‐ductile in the axial positioning, with a maximum erosion rate at a 60° impingement angle. However, these composite pipes' inner surfaces in the same positioning presented a maximum erosion rate at a 45° impingement angle. Besides, it is explored that the GnPs contribute to an improvement of approximately 10%–55% in erosive wear resistance of the non‐reinforced BFRP composite pipes. The damage analysis of eroded surfaces was examined through scanning electron microscopy (SEM), and the GnPs effect upon composite pipes' erosion micromechanisms was presented and discussed in detail.Highlights: GnPs increased the BFRP composite pipe's erosion resistance. Erosion rate on the inner surface increases due to particle accumulation. GnPs improved erosion behavior via solid lubrication and mechanical properties.

8 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
HSHarun Sepetcioglu
Harun Sepetcioglu
MBMehmet Bagci
Mehmet Bagci
Basalt/epoxy composite pipes in a [±55]4 winding configuration were produced on CNC filament winding machines (10 N fiber tension and ~11 mm bandwidth). In the experiments, a 34 m/s impact velocity was set using the double-disc method, and five different particle impingement angles (30, 45, 60, 75, and 90°) were used to determine the erosive effect on the outer surfaces of filament wound composite pipes under the influence of 600 μm erodent particles with angular geometry in the test set, complying with the ASTM G76-95 standard. The winding patterns in the lamina (±55 angle-ply laminate region) and zigzag (±55 zigzag region) regions of BFR/EP pipes were determined to have significant effects on solid particle erosion resistance, as evidenced by the SEM images.


21 May 2025 in Polymer Composites
Verified
Journal Article
Open access
HSHarun Sepetcioglu
Harun Sepetcioglu
SDSeyit Mehmet DEMET
Seyit Mehmet DEMET
İdris KARAGÖZİdris KARAGÖZ
İdris KARAGÖZ
MBMehmet Bagci
Mehmet Bagci
The aim of this study is to investigate the solid particle erosion behavior of walnut shell (WS)‐filled acrylic‐styrene‐acrylate (ASA) and polycarbonate/acrylic‐styrene‐acrylate (PC/ASA) thermoplastic blend composites under various erosion conditions. Erosion resistance tests were conducted using Al 2 O 3 particles (600 μm, Mohs hardness 9) as erodent, at a velocity of 34 m/s, with impingement angles ranging from 30° to 90°. Test samples were subjected to these conditions for 24 s, and weight loss was measured to determine erosion rates. Key parameters such as density, hardness, and erosion coefficients were also evaluated. Composites with 10 wt% WS filler exhibited optimal performance, reducing erosion rates by up to 36.7% compared to unfilled PC/ASA blend. Macro and SEM imaging revealed the damage mechanisms, showing less material loss and better surface durability in WS‐filled composites. This study demonstrates that incorporating WS into ASA and PC/ASA matrices not only improves erosion resistance but also aligns with the goal of sustainable material development. The results suggest that these composites could be highly effective in industries where materials are exposed to wear and tear from abrasive forces, such as in construction or automotive applications.

30 January 2021 in Tribology Letters
Verified
Journal Article
Closed access
PDF file
MDMusa Demirci
Musa Demirci
MBMehmet Bagci
Mehmet Bagci

9 July 2021 in Surface Topography: Metrology and Properties
Verified
Journal Article
Closed access
MDMusa Demirci
Musa Demirci
MBMehmet Bagci
Mehmet Bagci
Two different protective MCrAlY (NiCrAlY and NiCoCrAlY) coatings were obtained using the Atmospheric Plasma Spray (APS) method on the Inconel 718 substrate. It is aimed to inspect the rate of erosion and increase working life in last stage components of gas turbines, turbine blades and vanes. Because of the nature of exhaust, they are exposed the high temperature solid particle erosion. The High Temperature Solid Particle Erosion (HTSPE) test rig, which was specially designed and manufactured in accordance with the internationally accepted standard of ASTM G211–14, was used in the experiments. The experiments were conducted with three different air temperatures (room temperature, 300 °C and 600 °C), three different erosive particle impact angles (30°, 60° and 90°), constant particle impact velocity (∼97 m s −1 ) and particle size (400 μ m Al 2 O 3 ). SEM images, XRD analysis, EDX mapping and EDX element analysis were used to characterize the coatings. The erosion resistance results were interpreted with respect to the porosity values, hardness and surface roughness measurements of the coatings in details. As a result of the experiments, MCrAlY coatings showed ductile material behaviour compatible with erosion wear, and the cobalt element added to the coating structure contributed positively to increasing erosion resistance.