This paper investigates energy efficiency and dynamic behavior through simulation and experiments of a compact electro-hydrostatic actuator system (EHA) consisting of an electric motor, external gear pump/motors, hydraulic accumulator, and differential cylinder. Tests were performed in a stand-alone crane in order to validate the mathematical model. The influence and importance of a good balance between pump/motors displacement and cylinder areas ratios is discussed. The overall efficiency for the performed motion is also compared considering the capability or not of energy recovery. The results obtained demonstrate the significant gain of efficiency when working in the optimal condition and it is compared to the conventional hydraulic system using proportional valves. The proposed system presents the advantages and disadvantages when utilizing components off-the-shelf taking into account the applicability in mobile and industrial stationary machines.

This paper investigates the effect of extra weight caused by the Direct Driven Hydraulics (DDH) in a micro-excavator. These projects are investigating the implementation of zonal or decentralized hydraulics for non-road mobile machinery (NRMM) and stationary industrial applications. The benefit of DDH is the combination of electric and hydraulic technologies in a compact package compared to conventional hydraulics, which enables a reduction of potential leakage points, flexible tubing, and boosting of the system efficiency due to switching to direct pump control instead of a loss-generating conventional valve-based control. In order to demonstrate these benefits for the excavator case, this paper proposes a system model approach to assess and predict energy consumption of the zonal hydraulics approach implemented with DDH in various working cycles, complemented by a structural analysis. The finite element analysis utilized for this demonstrated that the extra weight and selected location of DDH units do not negatively affect the structure of the excavator. Simulation results demonstrated that the energy consumption is approximately 15% higher with extra weight added by the three DDH units. Although approximately 20% more regeneration energy is produced, taking into account the regeneration energy, the increases in energy consumption are about 12%.

Direct driven hydraulic drives (DDH) have the advantages of compact high power density in hydraulic systems and flexible control of electric motors. These advantages can benefit non-road mobile machinery (NRMM) applications. However, maintaining high efficiency while working in sub-zero conditions with NRMM is challenging. Therefore, this paper investigates the effect of hydraulic oil on the efficiency of a DDH in a cold environment for an NRMM application. In the DDH setup, the speed and position control of a double-acting cylinder was implemented directly with an electric motor drive in a closed-loop system without the conventional control valves. Efficiency measurements of the DDH setup with two oils (conventional multi-grade and high-performance) were conducted under different operating conditions (speed and payload) and environmental conditions (temperature in °C). The paper provides an evaluation of the electro-hydraulic system and a discussion on the usage of hydraulic oil by non-road mobile working machines in sub-zero conditions. An experimental investigation demonstrated an improvement in efficiency of 5%-unit at 22 °C, from 2%-unit to 5%-unit at 3 °C, and of almost a 10%-unit at temperatures below zero (−10 °C) by changing oil.

In this experimental study, a Direct Driven Hydraulics (DDH) system of the closed circuit type was utilized for cyclic vertical actuation in heavy load material handling. The actuator was controlled by a speed-controlled fixed displacement pump. The high energy saving potential of this system has been demonstrated in previous studies by the authors, but the dynamic characteristics of the ramped and P-controlled base system were considered unsatisfactory. Therefore, the system was implemented with an open-loop S-curve control that utilized a pre-calculated RPM (revolutions per minute) profile for the electric motor in order to realize a smooth actuator and load transition as a function of time. The results indicate that S-curve control is exceptionally well suited for producing a controlled lifting–lowering rapid motion with a heavy load, while still keeping the actuator chamber pressures within acceptable limits. In comparison, the motion produced by P-control was characterized by large unwanted pressure peaks together with velocity fluctuations and vibrations at the end of the stroke. Using a combination of S-curve control and hydraulic load compensation, a mass of 1325 kg could be moved 0.26 m in less than 0.5 s. The load compensation reduced the energy consumption by 64%, which would allow downsizing the electric motor and enable cost-efficient DDH implementation.

Electro-hydrostatic actuators (EHAs) are emerging transmission techniques originated from aerospace industry and being introduced to various application fields, such as ships, robots, construction machines, and machine tools. Despite the advantages of high efficiency, easy maintenance, electrified power, etc., EHAs are usually self-contained integrated devices, resulting in low heat dissipation ability. Therefore, thermal coupling models are necessary for the evaluation of each design option during the EHA development. In this paper, a thermal coupling model was established for EHA thermal characteristic analysis during the detail design stage. The disciplines of electrics, mechanics, system level hydraulics, losses, and control are implemented by lumped parameter modeling while the disciplines of thermodynamics and fluid dynamics are simulated by computational fluid dynamics (CFD). Subsequently, a simulation analysis focusing on the critical temperature conditions was conducted, and the dynamic thermal and power responses were achieved. The simulation results are applicable to gain confidence for EHA detail design work as well as proved the functions of the proposed model as a practical development tool.