Souad Boumad

Dr. Souad Boumad

Chemical engineering, Blida1 University, Blida, Algeria
Associate professor

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2024 in Environmental Research
Verified
Journal Article
Open access
SBSouad Boumad
Souad Boumad
LCL. Cano-Casanova
L. Cano-Casanova
MRM.C. Román-Martínez
M.C. Román-Martínez
NBN. Bouchenafa-Saib
N. Bouchenafa-Saib
Maria Angeles Lillo-RodenasMaria Angeles Lillo-Rodenas
Maria Angeles Lillo-Rodenas
The literature rarely compiles studies devoted to the removal of pollutants in aqueous media comparing adsorption and photocatalytic degradation, and does not pay enough attention to the analysis of combined adsorption-photocatalytic oxidation processes. In the present manuscript, the removal of malachite green (MG) from aqueous solutions has been investigated in three different sustainable scenarios: i) adsorption on activated carbon (AC) derived from a residue, luffa cylindrica, ii) photocatalytic oxidation under simulated solar light using titanium dioxide (TP) and iii) combined adsorption-photocatalytic oxidation using TP-AC (70/30 wt./wt.) under simulated solar light. The study has revealed that in the three scenarios and studied conditions, the total removal of this endocrine-disrupting dye from the solution takes place in the assayed time, 2 h, in some cases just in a few minutes. MG adsorption in the AC is a very fast and efficient removal method. MG photocatalytic oxidation with TP also occurs efficiently, although the oxidized MG is not totally mineralized. MG removal using the TP-AC composite under simulated solar light occurs only slightly faster to the MG adsorption in the AC, being adsorption the dominating MG removal mechanism for TP-AC. Thus, more than 90% of the removed MG with TP-AC under simulated solar light is adsorbed in this carbon-containing composite. The obtained results highlight the interest in adsorption, being the selection of the most suitable removal method dependent on several factors (i.e., the cost of the AC regeneration, for adsorption, or the toxicity of the intermediate oxidation species, for photooxidation). Paying attention to MG photooxidation with TiO2, comparison of two working photodegradation schemes shows that the direct photodegradation of MG from solution, avoiding any initial dark equilibrium period, is more efficient from a time perspective. The use of scavengers has proved that MG photodegradation occurs via an oxidation mechanism dominated by superoxide anion radicals.

19 August 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SBSouad Boumad
Souad Boumad
Antonia Infantes-MolinaAntonia Infantes-Molina
Antonia Infantes-Molina
IMIsabel Barroso Martín
Isabel Barroso Martín
Elisa MorettiElisa Moretti
Elisa Moretti
Enrique Rodriguez-CastellonEnrique Rodriguez-Castellon
Enrique Rodriguez-Castellon
NBNaima Bouchenafa-Saib
Naima Bouchenafa-Saib
This research aims to study the possible improvement of methylene blue (MB) removal from aqueous solution by hybrid adsorbent-catalysts (AdsCats) prepared through the incorporation of activated carbon derived from Luffa cylindrica fibers (LAC) to TiO2 photocatalysts. LAC with a specific surface area of 1170 m2/g was prepared by chemical activation with phosphoric acid at 500 °C. TiO2/LAC composites with 70 and 90 wt.% Degussa P25 titania content were prepared. The materials were characterized by N2 physical adsorption, XRD, FTIR, and XPS. The AdsCats displayed a very good dispersion of TiO2 over LAC, a surface area of close to 200 or 400 m2/g, depending on the composition, and high crystallinity, showing the presence of anatase and rutile phases. MB removal was studied in two different scenarios: under UV-light after reaching adsorption equilibrium, and under UV-light once the liquid effluent and the AdsCats were in contact. The MB removal by LAC has proved to be very efficient, highlighting the predominant role of adsorption over photodegradation. The prepared AdsCats have also been compared with their components. The results showed that TiLAC hybrids have superior photocatalytic performance than P25, showing TiLAC-7/3 90% MB removal with respect to the initial concentration just after 30 min of UV light irradiation for both studied scenarios.

22 November 2022 in C
Verified
Journal Article
Open access
PDF file
NMNesrine Madani
Nesrine Madani
Imane MouleferaImane Moulefera
Imane Moulefera
SBSouad Boumad
Souad Boumad
Diego Cazorla-AmorósDiego Cazorla-Amorós
Diego Cazorla-Amorós
FGFrancisco José Varela Gandía
Francisco José Varela Gandía
NBNaima bouchenafa Bouchenafa-Saib
Naima bouchenafa Bouchenafa-Saib
The Stipa tenacissima S. is an endemic species of the Western Mediterranean countries, which grows on the semi-arid grounds of North Africa and South Spain. This biomass offers an abundant, renewable, and low-cost precursor for the production of activated carbon (AC). In that context, ACs were prepared by chemical activation of Stipa tenacissima leaves (STL) using phosphoric acid (H3PO4). The effects of activation temperature and impregnation ratio on the textural and chemical surface properties of the prepared activated carbons were investigated. Activation temperatures of 450 and 500 °C turned out to be the most suitable to produce activated carbons with well-developed porous textures. The best results in terms of developed surface area (1503 m2/g) and micropore volume (0.59 cm3/g) were observed for an STLs to phosphoric acid ratio of 1:2 and a carbonization temperature of 450 °C. The adsorption capacity of the optimal activated carbon was found to be 110 mg/g for the atenolol drug. The adsorption equilibrium was well explained by the pseudo-second-order model and Langmuir isotherm. This study showed that the chemical activation method using H3PO4 as an activating agent was suitable for developing STL-based activated carbon prepared for the removal of atenolol drug in an aqueous solution and compared with commercial activated carbon supplied by Darco.


31 January 2026 in Journal of Polymer Research
Verified
Journal Article
Open access
PDF file
ABAmina Bekhoukh
Amina Bekhoukh
Imane MouleferaImane Moulefera
Imane Moulefera
SBSouad Boumad
Souad Boumad
Abdelghani BenyoucefAbdelghani Benyoucef
Abdelghani Benyoucef
The incorporation of conducting polymers with nanostructure materials offers a promising route to multifunctional materials with improved electrochemical and thermal properties. In this study, poly(2-anisidine) (P(2-ANIS)), a methoxy-subst ituted derivative of polyaniline, was synthesized via oxidative polymerization and combined with titanium carbide(TiC) nanoparticles to form hybrid nanocomposites. Two methods were used : in situ polymerization, where TiC was present during polymer preparation, and ex situ method, where TiC was introduced after polymer obtained. Comprehensive characterization including XRD, FTIR, TEM, TGA, UV–Vis, cyclic voltammetry, and electrical con ductivity measurements was carried out to evaluate the effect of each method on the structural, thermal, and electronic properties of the composites. Results display that the in-situ method yields high particle dispersion, stronger interfacial interaction, enhanced electrochemical redox activity, and higher thermal stability compared to the ex-situ polymerization. However, the incorporation of TiC nanoparticles into the P(2-ANIS) matrix resulted in an increase in the optical band gap and a moderate decrease in electrical conductivity compared to the pure P(2-ANIS). These results demonstrate the influence of the synthesis method on the structural properties of P(2-ANIS)@TiC nanocomposites and provide valuable insight into tailoring polymer nanoparticle interfaces for advanced functional applications.