The effects of the Y- and Ti-containing inclusions on the tensile and impact properties of reduced activation ferritic martensitic (RAFM) steels were evaluated. Four steels with different Y and Ti contents were produced via vacuum induction melting. The size and quantity of inclusions in the steels were analyzed using scanning electron microscopy, and the oxide particle formation mechanism was clarified. These inclusions helped to enhance the pinning effect of the austenite grain boundaries based on the Zener pinning force. The average prior austenite grain sizes, measured via the linear intercept method, were 12.34 (0 wt.% Ti), 9.35 (0.010 wt.% Ti), 10.22 (0.030 wt.% Ti), and 11.83 (0.050 wt.% Ti) μm for the four steels, in order of increasing Ti content, respectively. Transmission electron microscopy was conducted to observe the fine carbides. The strength and impact properties of the steel containing 0.010 wt.% Ti were improved, and the ductile-to-brittle-transition temperature was reduced to −70.5 °C. The tensile strength and impact toughness of the steel with 0.050 wt.% Ti were significantly reduced due to the coarsening of both the inclusions and grain size, as well as the precipitation of large TiN inclusions. The RAFM steel with approximately 0.015 wt.% Y and 0.010 wt.% Ti exhibited an optimized combination of microstructures, tensile properties, and impact properties among the four steels.

The problem of nitrogen pickup in the smelting process of the electric arc furnace (EAF) has not been solved well. Using seven slag–steel equilibrium experiments and theoretical analysis, the relation of the foaming index and optical basicity with the nitrogen capacity of slag was clarified. Meanwhile, the effect of slag composition on the equilibrium distribution ratio of nitrogen and the mass transfer coefficient of nitrogen pickup was also studied. The results show that, with the increase in slag basicity, the nitrogen pickup amount, nitrogen pickup rate, and nitrogen equilibrium distribution ratio L_N increase. Increasing the foaming index of slag and reducing its optical basicity will increase the nitrogen capacity of slag, which is conducive to hindering the nitrogen pickup of molten steel. The relationship between slag optical basicity and nitrogen capacity can be expressed as lgC_N = −5.59lgΛ − 12.41. With the increase in the Al₂O₃ content of slag, the nitrogen pickup amount of molten steel decreases and the nitrogen pickup rate decreases. The test with MgO = 7.5% showed the highest nitrogen pickup rate and the highest nitrogen pickup mass transfer coefficient, which were 0.21 × 10⁻⁴%/min and 1.97 × 10⁻⁴ cm/s, respectively. The test with Al₂O₃ = 7.5% in slag showed the lowest nitrogen pickup rate and the lowest nitrogen pickup mass transfer coefficient, which were 0.08 × 10⁻⁴%/min and 1.35 × 10⁻⁴ cm/s, respectively.

This study investigated the microstructural stability and mechanical properties exhibited by China low activation martensitic (CLAM) steels with different yttrium (Y) contents over 3000 h of aging at 550 °C. Scanning electron microscopy, electron backscatter diffraction analysis, and transmission electron microscopy were employed to investigate the microstructural evolution of the steels. Results indicated that grain boundary migration was slow and the Laves phase precipitation was delayed in Y-containing steels. Grain boundaries at different angles in 0Y and 6Y CLAM steels were significantly affected, and those in 36Y and 71Y alloys exhibited negligible changes during the long-term thermal aging. Moreover, Y contents had appreciable effects on the strength and toughness of the aged steels. The stable microstructure of Y-containing CLAM alloys is responsible for improved strength and impact toughness during aging.

In this study, we present the effects of 0.004~0.098 wt% Zr and thermo-mechanical processing (TMP) on the microstructure and mechanical properties of the China RAFM steel, CLAM, as a feasibility study for improving mechanical properties. The inclusions in ingots were characterized using optical microscope (OM) and scanning electron microscope (SEM), which could be classified as fine simple particles and large complex particles. The complexity of the alloy’s inclusion composition increases with the increasing Zr concentration. The higher the Zr content, the more complex the composition of inclusions in the alloy. The average diameter of inclusions in 0.004Zr steel was the smallest, which was 0.79 μm and the volume fraction was 0.018%. The highest yield strength, tensile strength, elongation, and impact energy of 0.004Zr alloy at room temperature were 548.3 MPa, 679.4 MPa, 25.7%, and 253.9 J. The structure of the TMPed steels was all tempered martensite. With the increase in tempering temperature, the yield and tensile strength of the experimental steel gradually decreased, while the elongation and impact energy gradually increased. The 0.004ZrD and 0.004ZrH alloys had the best yield strength and impact energy, which were 597.9 and 611.8 MPa and 225.9 and 243.3 J, respectively. In addition, the alloys showed good thermal stability during the aging at 600 °C for 1500 h. It was discovered that TMP is a simple and practical industrial technique that could successfully enhance the mechanical properties of CLAM steel without sacrificing impact toughness.