Sebastian Johann Müllner

Mr. Sebastian Johann Müllner

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 April 2023 in Batteries
Verified
Journal Article
Open access
PDF file
SMSebastian Johann Müllner
Sebastian Johann Müllner
TMTobias Michlik
Tobias Michlik
MRMichael Reichel
Michael Reichel
THTilo Held
Tilo Held
Ralf MoosRalf Moos
Ralf Moos
CRChristina Roth
Christina Roth
Silicon-containing materials are still the most promising alternatives to graphite as the negative electrodes of lithium-ion batteries. However, the different Li+ storage mechanism combined with the high capacity result in new requirements for the passive electrode components, such as the binder. To ensure sufficient cycling stability, silicon must be embedded in a suitable carbonaceous matrix. For this purpose, we used a simple ball milling process with reduced graphene oxide (rGO) to produce Si-rGO composites with µm- and nm-sized silicon particles. The rGO was synthesized previously from a two-step thermal synthesis method developed in-house. Subsequently, electrodes with varying CMC/SBR ratios (3:1, 1:1, and 1:3) were prepared from the composites containing the different Si particle sizes. It was found that the optimal binder ratio depends on the size of the Si particles. For the nm-Si-rGO composite, a CMC/SBR ratio of 3:1 results in a total capacity over 51 cycles of 20.6 Ah g−1, which means an improvement of 20% compared to CMC/SBR = 1:3 (17.1 Ah g−1). In contrast, we demonstrate that for µm-Si-rGO composites with an optimal CMC/SBR ratio of 1:1 (13.0 Ah g−1), compared to nm-Si-rGO, a higher SBR content is beneficial for the cycling behavior. Moreover, a comparison with graphite from the literature indicates that a rGO-matrix reduces the need for SBR.

1 July 2023 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
SMSebastian Johann Müllner
Sebastian Johann Müllner
THT. Held
T. Held
TTT. Tichter
T. Tichter
PRPhilipp Rank
Philipp Rank
DLD. Leykam
D. Leykam
CRChristina Roth
Christina Roth
Most high capacity anode materials for lithium-ion batteries (LiB) require a carbonaceous matrix. In this context one promising material is reduced graphene oxide (rGO). Herein, we present the influence of different reduction degrees of rGO on its physico-chemical properties, such as crystallinity, specific surface area, electrical conductivity and electrochemical lithiation/delithiation behavior. It is found that a heat treatment under inert and reducing atmospheres increases the long-range order of rGO up to a temperature of 700 °C. At temperatures around 1000 °C, the crystallinity decreases. With decreasing oxygen content, a linear decrease in irreversible capacity during cycle 1 can be observed, along with a significant increase in electrical conductivity. This decrease in irreversible capacity can be observed despite an increase in specific surface area indicating the more significant influence of the oxygen content on the capacity loss. Consequently, the reversible capacity increases continuously up to a carbon content of 84.4 at% due to the thermal reduction. Contrary to expectations, the capacity decreases with further reduction. This can be explained by the loss of functional groups that will be lithiated reversibly, and a simultaneous reduction of long-range order, as concluded from dq/dU analysis in combination with XRD analysis.

1 December 2021 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
SMSebastian Johann Müllner
Sebastian Johann Müllner
THT. Held
T. Held
ASA. Schmidt-Rodenkirchen
A. Schmidt-Rodenkirchen
TGT. Gerdes
T. Gerdes
CRChristina Roth
Christina Roth
Lithium-ion batteries with Si anodes are still attracting increasing attention, particularly due to the high specific energy density. The main disadvantage of silicon as anode material is its reduced cell performance in terms of cycling stability. One promising approach to improve this is embedding silicon nanoparticles in a graphene-like matrix via spray drying. All processes described so far need a time- and energy-intensive two-step-synthesis to obtain the graphene-like rGO structure. Here, we present a reactive spray drying process for synthesis of Si/rGO composites. For proper reactor design, the reaction kinetics are investigated by simultaneous thermal analysis in various atmospheres. We can describe thermal decomposition of GO to rGO as a second-order reaction. STA data also show that additional presence of water in the atmosphere due to the one-step synthesis is negligible at temperatures below 600 °C for both the reaction of GO and the additional oxidation of Si. To evaluate the electrochemical performance, the composites are cycled in a half cell setup. Delithiation capacity after cell formation could be raised from 252 mAh g −1 for GO to 327 mAh g −1 for rGO. In addition, we are able to synthesize Si-containing composites suitable for the anode of LiB using our process.

22 October 2025 in Batteries
Verified
Journal Article
Open access
PDF file
PRPhilipp Rank
Philipp Rank
SMSebastian Johann Müllner
Sebastian Johann Müllner
TGThorsten Gerdes
Thorsten Gerdes
CRChristina Roth
Christina Roth
The thermal characteristics and surface properties of battery separators are commonly modified by the incorporation of inorganic particles into a polymeric matrix material. At present, the particles employed are predominantly of an arbitrary shape. Herein, we demonstrate significantly improved battery safety features using a glass-based separator consisting of platelet-shaped particles. Glass is selected due to its temperature stability and the freedom of design that it offers when particles are formed directly from the melt. The influence of the particles’ aspect ratio and layer stacking on the electrochemical properties was analyzed, and a parametric study of glass particle layers as function of edge length and thickness was conducted. Particles with an excessively high aspect ratio impede the Li+ diffusion pathway, thereby negatively affecting the performance and stability of the battery cell. Conversely, if the aspect ratio is insufficient, a deterioration in cell performance can be observed, particularly at elevated C-rates, due to the high specific surface area of the particles. Hence, the utilization of particles with a moderate aspect ratio of about 10 and a thickness of around 1 µm is proposed to ensure optimum performance.

22 December 2023 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
THTilo Held
Tilo Held
SMSebastian Johann Müllner
Sebastian Johann Müllner
LWLukas Wölfel
Lukas Wölfel
CRChristina Roth
Christina Roth
An attractive approach to increase the Li+-storage capacity of anode materials in Lithium-ion batteries (LiBs), is to replace or combine the routinely-applied graphite (372 mAh g-1) with higher-capacity materials. Among others, silicon (Si) with a theoretical capacity of 3579 mAh g-1 is a promising candidate [1]. Silicon is not yet been used as an anode material in its pure form, due to its low conductivity and volume increase of up to 300 % during lithiation. This two-step expansion (1st: Si + 2 Li+ + 2 e- → SiLi2.0; 2nd: SiLi2.0 + 1.5 Li+ + 1.5 e- → SiLi3.5) is a source of mechanical stress that can ultimately lead to battery failure. Furthermore, the initial lithiation of crystalline silicon (c-Si + 3.5 Li+ + 3.5 e- → SiLi3.5) causes an amorphization of the pristine crystalline lattice. This structural change causes further degradation of the material, which can hardly be avoided [2]. The main degradation mechanisms resulting from expansion and amorphization are I) The uncontrolled formation of a passivation layer due to the cyclic volume change taking place during (de-)lithiation, which leads to a continuous break-up and reformation of the solid electrolyte interphase (SEI). II) The pulverization of particles resulting in mechanical stress and the electrical isolation of particles or particle fragments delaminating from the electrode [3]. The first mechanism discussed is more dominant for nanometer scaled particles (nm-Si), while the second mechanism occurs mostly for particles in the micrometer range (µm-Si). Our approach combines, nm- or µm-sized Si particles with different matrix materials. By incorporating the particles into an either graphitic or soft carbon-like support, we aim to increase the conductivity of the electrode material and gain additional buffer space thereby reducing interparticle mechanical stress [4]. On the one hand, the systems of carbon-based anode materials are already well understood in terms of electrode composition, processing parameters, electrolyte compatibility, formation of a stable SEI and the resulting high cycling stability. On the other hand, the observed degradation mechanisms will occur with different predominance in different Si/C composites depending on the Si particle size and the chosen carbon matrix. However, the latter is not completely understood. We will address these issues by comparing different Si/C-composites consisting of nm-Si-particles or µm-Si particles in a reduced graphite oxide (rGO) matrix and in a graphite-matrix. Electrochemical methods, such as galvanostatic cycling, impedance spectroscopy and dq/dU-analysis in 2- and 3-electrode setups, were coupled with optical and spectroscopical techniques (e.g. XRD, FTIR, SEM) to trace back the electrochemically measurable degradation of the electrode to structural changes during formation and cycling. Particular attention was paid to the localization and analysis of defect areas with increased degradation by correlating the optical and spectroscopical results data with the lithiation and delithiation processes. Considering the different SoC levels, we can identify the ongoing aging of the different electrode materials. Based on this, we propose the use of soft carbon-like structures such as rGO as a matrix material for Si/C composites due to its higher cycling stability under the investigated conditions. References [1] Jeschull, F., Surace, Y., Zürcher, S., Lari, G., Spahr, M. E., Novák, P. u. Trabesinger, S.: Graphite Particle-Size Induced Morphological and Performance Changes of Graphite–Silicon Electrodes. Journal of The Electrochemical Society 167 (2020) 10, S. 100535 [2] Graf, M., Berg, C., Bernhard, R., Haufe, S., Pfeiffer, J. u. Gasteiger, H. A.: Effect and Progress of the Amorphization Process for Microscale Silicon Particles under Partial Lithiation as Active Material in Lithium-Ion Batteries. Journal of The Electrochemical Society 169 (2022) 2, S. 20536 [3] Dienwiebel, I., Winter, M. u. Börner, M.: Visualization of Degradation Mechanisms of Negative Electrodes Based on Silicon Nanoparticles in Lithium-Ion Batteries via Quasi In Situ Scanning Electron Microscopy and Energy-Dispersive X-ray Spectroscopy. The Journal of Physical Chemistry C 126 (2022) 27, S. 11016–11025 [4] Müllner, S., Held, T., Schmidt-Rodenkirchen, A., Gerdes, T. u. Roth, C.: Reactive Spray Drying as a One-Step Synthesis Approach towards Si/rGO Anode Materials for Lithium-Ion Batteries. Journal of The Electrochemical Society 168 (2021) 12, S. 120545

22 December 2023 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
PRPhilipp Rank
Philipp Rank
SSSarah Spreng
Sarah Spreng
SMSebastian Johann Müllner
Sebastian Johann Müllner
CRChristina Roth
Christina Roth
TGThorsten Gerdes
Thorsten Gerdes
Lithium-ion batteries (LIBs) are one of the most important and common energy storage technologies for mobile devices as well as electric vehicles due to their high specific energy density [1]. However, there are still safety concerns in case of overcharge or mechanical damage. The separator as the passive safety-relevant component is placed between the two electrodes to prevent internal short-circuits. Nevertheless, accidental or inhomogeneous deposition of metallic lithium (Li plating) can lead to dendrite growth, which is one of the most common failure mechanisms. If only one dendrite penetrates the separator and forms a conductive path between the two electrodes, a short circuit in the battery leads to its failure [2]. Despite the inherent rigidity of glass materials, previous studies demonstrated the successful application of glass-based separators in LIBs [3, 4]. To meet the requirements of modern battery production, a colloidal water-based system of glass particles and binder is used to manufacture flexible separators. Compared to state-of-the-art polymer-based separators, those flexible glass particle-based separators are superior in many of the required properties such as higher temperature resistance and dimensional stability up to 600 °C [3]. However, the size and morphology of the utilized particles have a significant impact on the manufacturing process, e.g. affect slurry processability and separator formation, and consequently on the electrochemical performance. The effects of these parameters have already been studied for spherical or arbitrarily-shaped particles [5, 6]. In the present work, platelet-shaped particles are utilized to manufacture glass-based separators. To further improve the operational safety of lithium-ion batteries, the benefit of platelet-shaped particles is compared to the use of arbitrarily-shaped particles. The use of these so-called glass flakes serves the purpose of forming an effective barrier against growing lithium dendrites by establishing a self-stabilizing structure. This barrier prevents or at least effectively delays penetration of the separator. For platelet-shaped particles, thickness and edge length of a particle differ significantly. Particles with a too high aspect ratio (edge length to thickness) block the Li+ diffusion pathway, affecting performance and stability of the final cell. Preliminary tests have shown that increasing the thickness of the glass flakes leads to a slight improvement of ionic conductivity, while increasing the edge length results in a strong reduction of ionic conductivity. However, separators containing particles with higher aspect ratio are expected to show increased piercing resistance. Thus, a trade-off between processability, electrochemical performance and safety barrier function against Li-dendrite growth and penetration is evaluated to understand the influence of particle morphology on the properties of separators using these particles. The microstructure of separators containing the different particle morphologies is examined using scanning electron microscopy (SEM) and correlated with the results of further characterization methods such as electrochemical impedance spectroscopy (EIS) and galvanostatic cycling. References [1] Liu, K., et al.: Materials for lithium-ion battery safety; Science Advances 4 (2018); eaas9820 [2] Wassiliadis, N., et al.: Review of fast charging strategies for lithium-ion battery systems and their applicability for battery electric vehicles; Journal of Energy Storage 44 (2021); 103306 [3] Schadeck, U., et al.: Flexible, Heat-Resistant, and Flame-Retardant Glass Fiber Nonwoven/Glass Platelet Composite Separator for Lithium-Ion Batteries; Energies 11 (2018) 4; 999–1013 [4] Schadeck, U., et al.: Porous and non-porous micrometer-sized glass platelets as separators for lithium-ion batteries; Journal of Membrane Science 550 (2018); 518–525 [5] Takemura, D., et al.: A powder particle size effect on ceramic powder based separator for lithium rechargeable battery; Journal of Power Sources 146 (2005); 779–783 [6] Kanhere, N., et al.: Electrode-coated alumina separators for lithium-ion batteries - effect of particle size and distribution of alumina powders; Powder Technology 353 (2019); 230–237