In recent years, inverse gas chromatography (IGC) and molecular dynamics simulation methods have been used to characterize the solubility parameters and surface parameters of polymers, which can provide quantitative reference for the further study of the surface and interface compatibility of polymer components in the future. In this paper, the solubility parameters and surface parameters of two kinds of common alcoholysis, PVA88 and PVA99, are studied by using the IGC method. The accuracy of the solubility parameters obtained by the IGC experiment is verified by molecular dynamics simulation. On the basis of this, the influence of repeated units of polyvinyl alcohol (PVA) on solubility parameters is studied, so as to determine the appropriate chain length of the PVA for simulation verification calculation. The results show that the solubility parameters are not much different when the PVA chain length is 30 and above; the numerical trends of the solubility parameters of PVA88 and PVA99 at room temperature are the same as the results of molecular dynamics simulation; the dispersive surface energy and the specific surface energy are scattered with the temperature distribution and have a small dependence on temperature. On the whole, the surface energy of PVA99 with a higher alcoholysis degree is higher than that of PVA88 with a lower alcoholysis degree. The surface specific adsorption free energy () indicates that both PVA88 and PVA99 are amphoteric meta-acid materials, and the acidity of PVA99 is stronger.
1 October 2021 in Plasma Sources Science and Technology
The azimuthal currents in the divergent magnetic nozzle of the electrodeless plasma thrusters are investigated using a two-dimensional axisymmetric particle-in-cell code. In this paper, the azimuthal currents are decomposed into four components—the diamagnetic drift current, the E × B drift current, the viscous-stress-induced current and the inertia-induced current. The azimuthal current and its four components are analyzed under three magnetization levels of 0.25 T, 0.75 T and 2.15 T. In the absence of inlet ion temperature, the azimuthal currents mainly consist of electron currents resulted from ∇ pe , E × B drift and electron viscosity, while the azimuthal currents caused by the inertia can generally be neglected. The azimuthal ion currents considered negligible in previous studies are shown to be non-negligible in the highly-magnetized and collisionless magnetic nozzle, where the dominant mechanism for its formation is E × B drift and drift from the centrifugal force. In the upstream and midstream, the compositions and distributions of the azimuthal currents can vary at different radial positions and magnetization conditions because of the influence of the electric potential barrier and the high density conic. In the downstream, a vast range of paramagnetic currents are produced by the E × B drift due to ion inward detachment. And the paramagnetic stress-induced current begins to prevail due to the FELR effect. Superimposed with the paramagnetic part of the diamagnetic drift current under a high magnetic field, they can undermine the thrust gain coefficient of the magnetic nozzle.
The particle-in-cell-Monte Carlo collision method has been widely used in simulation studies of ion thrusters. Due to the huge computational demand of such simulations, numerical acceleration techniques are required. However, the effects of such numerical acceleration techniques on the simulation results are not clear. In this study, the effects of three numerical acceleration techniques are investigated using a series of simulations that implement different numerical acceleration factors. The resulting plasma potentials, plasma density distributions, and plasma currents in the discharge chamber are compared for simulations accelerated by increasing the vacuum permittivity, reducing the mass of heavy particles, and making use of self-similarity. The results demonstrate that increasing the permittivity thickens the sheath. When the sheath expands enough to extend to the cusps, the distributions of the potentials and the plasma densities are affected, influencing the current parameters. Reducing the masses of heavy particles greatly influences ion properties, especially the plasma density. Thus, it causes significant errors in the potential and current parameters. Errors in the beam current can be significantly decreased by correcting the beam current using an exponent relationship between the mass scaling factor and the plasma density. The use of self-similarity simultaneously thickens the sheath and decreases the particle number density and may slightly reduce the plasma current values. A number of suggestions for employing these techniques are also provided.
It is challenging for ionic liquid gels to achieve the combination of rapid self-healing with high toughness. Here, ionic liquid gels (DI-PR) were prepared from readily available materials. A dynamic covalently bonded oxime–carbamate was prepared from polycaprolactone diol, isophorone diisocyanate and dimethylethyleneglyoxime, followed by addition of the “rigid-flexible” cross-linking agent rutin to chemically cross-link the polymer chains and afford the ionic liquid gels, DI-PR. The tensile strength, elongation at break and toughness of the DI-PR gels were as high as 16.5 MPa, 1132.6%, and 52.6 MJ m−3, respectively. The toughness is similar to that of natural silkworm silk (70 MJ m−3) and wool (60 MJ m−3). After stretching, the DI-PR can rebound within 1 s, their room temperature self-healing rate is as high as 92%, they remain functional over the temperature range −50 °C to 140 °C and the interface with a steel plate has an adhesion toughness of >2000 J m−2. These properties mean that the DI-PR gels are particularly suitable for use as anticorrosion coatings for submarine and underground gas and oil pipelines. The use of rutin, which combines rigid quercetin-based structural units with flexible glycoside-based structural units, as a cross-linking agent, provides a new method for improving the toughness of soft materials through its synergistic interaction with hard and soft chain fragments of polyurethanes.
1 May 2022 in Plasma Sources Science and Technology
A fully kinetic particle-in-cell study is conducted to investigate the ion acceleration mechanisms in an electron-driven magnetic nozzle. All five powers contributing to the axial kinetic energy of ions are derived and evaluated under different magnetic field strength and inlet density profiles. Among them, the electrothermal and electromagnetic acceleration contributes over 98% of the total accelerating power. The dominating acceleration mechanism is found to be the electrothermal acceleration, covering two thirds of the axial accelerating power in the electron-driven magnetic nozzle. The electromagnetic mechanism is found to originate from four sources, among which the major accelerating and decelerating one are the diamagnetic acceleration driven by radial gradient of electron pressure and the E × B mechanism due to the inward ion detachment. The power induced by the viscous-stress of electrons contributes 14%–23% of the decelerating power, indicating the non-negligible influence of finite electron Larmor radius effect on the ion acceleration. Results indicates that the net effect of electromagnetic mechanism can even be decelerating when the magnetic field is too high with a uniform inlet. Finally, the conversion efficiency from the inlet thermal energy to the ion axial kinetic energy is derived and evaluated, which can reach as high as 65.0% under 0.25 T with a Gaussian-profile inlet. Raising the magnetic field to 0.75 T or a uniform inlet will decrease the conversion efficiency.
Quantitative characterization of the solubility parameters and surface properties of larch bark proanthocyanidins will lay the foundation for quantitative studies of the interfacial interactions of proanthocyanidin/polymer composites and will improve the compatibility of components, with important practical and scientific significance. Here, the solubility parameters of highly polymerized larch polymeric proanthocyanidins (LPPCs) and less highly polymerized larch oligomeric proanthocyanidins (LOPCs) were determined experimentally by inverse gas chromatography (IGC). These values were then compared with the solubility parameters obtained using molecular dynamics simulations. The experimentally measured solubility parameters of LPPCs and LOPCs (20.5 and 22.09 (J/m−3)0.5, respectively) were in good agreement with the solubility parameters determined by molecular dynamics simulations (20.57 and 22.35 (J/m−3)0.5, respectively. IGC was also used to experimentally determine the total surface energy, which includes the dispersive component of surface energy and the specific component of surface energy , together with the surface acidity and basicity parameters of LPPCs and LOPCs at different temperatures. The surface properties of proanthocyanidins can be quickly and accurately evaluated by IGC, and both LPPCs and LOPCs were shown to be amphoteric materials. This study provides theoretical and technical support for the use of larch bark proanthocyanidins, which are non-toxic, renewable, and have good ultraviolet resistance, in the field of blending composites. The study also provides a reference for other studies on the interfacial interactions of wood fiber polymer composites.