The article examines the characteristics of sewage sludge and its impact on the environment. The description of technical installations, sludge sites in the city's sewage treatment systems, which are sources of unfavorable sanitary and epidemiological condition of the studied territory,...
The purpose of these studies is to investigate the dynamics of heavy metal pollution in the coastal zone and the marine part of the Caspian Sea in the Aktau Region of Kazakhstan in order to monitor the ecological state of the environment. Copper, nickel, arsenic, cadmium, chromium, lead and zinc concentrations have been detected in soil samples. Chromium, copper, nickel, lead and zinc concentrations have been detected in seawater samples. Physico-chemical analyses of soil and seawater samples taken in the coastal zone and the marine part of the Aktau Region were carried out using atomic absorption spectrometer. Experimental data were collected in 2018, 2019, 2021, 2023 and 2024 to reveal the existing trends in heavy metal concentrations. As concerns, contamination of soils there was a serious decrease in heavy metal concentrations from 2018 to 2023. In seawater, a decrease of heavy metal concentrations has been observed by 2021-2023, but unexpectedly almost all elements showed a slight increase in 2024. Anyway, in 2023 and 2024, concentrations of all heavy metals in soil and seawater samples remain well below the Maximum Permissible Concentrations. A significant reduction in heavy metal pollution is probably due to a successful environmental policy aimed at reducing emissions of pollutants and improving treatment systems. The obtained results allow to build recommendations for sustainable resource management and use of the coastal zones and water areas in the Aktau Region for policy-makers and end-users.
The world experience of neutralization and disposal of excess sludge of urban sewage is considered. The sludge generated during the technical treatment of municipal wastewater is dangerous, has low dehydration, the percentage of moisture is more than 96%, contains some pathogenic and organic substances, as well as heavy metals. In the Mangystau region of Aktau (Kazakhstan) at a sewage treatment plant, sewage sludge is mainly accumulated on silt sites after minimal treatment. The main directions of neutralization and disposal of excess sludge used in Asian and European countries are generalized. For example, while authors from China conducted research on ultrasonic chemical treatment of urban sludge and drying by artificial methods, authors from Europe paid more attention to the disposal of excess sludge from municipal wastewater, in the form of road surface additives, cement strength additives or modified bentonite for further use. Sewage sludge as a safe fertilizer in the national economy. Their advantages and disadvantages are shown, considering environmental and economic efficiency. The advantages of many studies can be indicated by the efficiency of the secondary use of sewage sludge, as well as a significant reduction in the area allocated for the storage of precipitation data. The disadvantages of these studies can indicate significant economic and time costs, which are ultimately compensated by the positive results of their secondary use.
The need for fresh water production is especially high in hot dry climates without any sources of drinking water but with an abundance of sea and underground water. The solution is water desalination with efficient solar-powered water treatment plants. This article proposes a new modification of a basin made of thin-finned corrugation with 43°-angle-inclined sides, equal to the region’s latitude, which provide strong heating. The experiments were carried out in the hot climate of Aktau city (43°49′ N, 51°1′ E). The study’s outcomes can be useful for regions with drinking water scarcity. To define the level of the corrugated basin’s efficiency, two versions (SS-1, SS-2) of experiments were carried out on a two-slope distiller, complete with two basins. In SS-1, basin-2 was heated by air. By 15:00, basin-2 had heated up to 98.5 °C, and the acrylic cover above had heated up to 101.6 °C, which led to its “deformation”. By 12.00 p.m., the temperature differentials between the glass (40.7 °C), the air–water mixture (57.3 °C), and basin-1 (61.1 °C) were 16.6 °C and 20.4 °C. This resulted from the wind speed increasing up to 5.9 m/s. The large temperature differential contributed to the condensate yield increasing from 0.128 kg at 11 o’clock to 0.293 kg at 12 o’clock. The throughput capability of basin-1 per day was equal to 2.094 kg. Basin-2’s input to the performance in SS-1 was only the thermal effect. In SS-2, basin-2 was used as a regular basin. The plexiglass temperature was lower than the temperatures of the water and basin-2. The temperature differential between the glass and air–water mixture at 10:00 a.m. was 20 °C; at 12:00 p.m. it was 30.6 °C; and a value of 30.6 °C was recorded at 3:00 p.m. The thermal differential between the glass and the air-water mixture provided the highest condensate yield of 1.114 kg at 3.00 p.m. The condensate yield from the basins in SS-2 was 8.72 kg, including 3.5 kg from basin-1, which is 1.7 times more than from basin-1 in SS-1. The experimental results are consistent with the equations coming from the models of Clark J.A. and Dunkle R.V. Tcondensation ≠ Tevaporation is an irreversible process. When the basins are heated, the heat is consumed; when the glass cools down, the heat is given off. Heat losses are minimized due to the “gap” and positive energy is provided. The still’s throughput capability can be made larger by increasing the basin’s area, reducing the water layer thickness, and regulating the flowrate of the desalinated water.
The article discusses the theoretical and practical aspects of modeling oil spills in the Caspian Sea. Special attention is paid to the development of numerical models capable of effectively predicting the trajectory and transformation of oil slicks under the influence of various natural and anthropogenic factors. It is noted that the accuracy of such models is largely determined by the completeness and reliability of the data entered: meteorological (wind speed and direction, air temperature), hydrological (currents, temperature and salinity of water, wave activity), as well as the physico-chemical characteristics of the oil itself (in particular, density on the API scale). The processes of evaporation, emulsification, dispersion, photochemical oxidation and sedimentation, which change the properties of oil during its distribution, also play an important role in modeling. The authors emphasize the importance of remote sensing and satellite technologies in detecting oil pollution and validating simulation results. Despite the high cost of such methods, they ensure the efficiency and scale of monitoring. The article also examines the behavior of Kashagan oil and the influence of ice phenomena characteristic of the northern part of the Caspian Sea on the spread of pollution. The paper describes the circulation processes in various parts of the sea that affect the transport of petroleum products. As a result of the performed analysis, the need to integrate numerical modeling with field observations is justified in order to increase the efficiency of forecasting and decision-making in emergency spill conditions. The findings have practical implications for environmental monitoring, strategic planning, and damage minimization in the event of oil pollution. These studies will provide an opportunity to fully assess the impact of oil spills on the marine ecosystem.