Jiří Začal

Dr. Jiří Začal

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 January 2023 in Symmetry
Verified
Journal Article
Open access
PDF file
JZJiří Začal
Jiří Začal
ZFZdeněk Folta
Zdeněk Folta
JSJiří Struž
Jiří Struž
MTMiroslav Trochta
Miroslav Trochta
This article discusses the issue of force behavior in a pre-tensioned bolt that is part of a symmetrical flange connection, loaded with an operating load parallel to the bolt axis. The first part describes the issue being dealt with in detail. The next part offers a brief description of the generally known theoretical approach to the solution, and also outlines the limitations of this approach. This part is followed by a theoretical analysis of working load behavior in the bolt of the analyzed device, using Finite Element Method (FEM). In this article, a comparison of several different approaches to the solution can be also found, followed by a description of the experiment preparation and its results. The obtained values also serve as a subject for reverse iterative analysis carried out using ANSYS software. The aim is to find a proper modification to the symmetric calculation model that would be consistent with the results of measurements from technical practice. All results achieved are described in the final part of the article.

15 December 2021 in MM Science Journal
Verified
Journal Article
Closed access
JZJiří Začal
Jiří Začal
JPJan Pavlik
Jan Pavlik
IKIvana Kunzova
Ivana Kunzova
The area of flange joints with gasket includes many types of pressure vessels, which are mainly defined by the purpose of use and specific load conditions. These differences in definitions caused the existence of many types of pressure vessels with different shell shapes. Calculations of basic sh...

17 December 2019 in Lecture Notes in Mechanical Engineering
Verified
Book Chapter
Closed access
PDF file
JZJiří Začal
Jiří Začal
LJLukáš Jančar
Lukáš Jančar

30 May 2023
Verified
Book Chapter
Open access
PDF file
LHLukáš Hruzík
Lukáš Hruzík
JSJiří Struž
Jiří Struž
JZJiří Začal
Jiří Začal
KKKvětoslav Kaláb
Květoslav Kaláb
This paper deals with design problematics of a clamping joint for the tanker frame in a rail vehicle. This car body is made from aluminum alloy. The main requirement of the joint is safe transmission the load given by the norm ČSN EN 12 663-1. At the beginning of the study is make the analysis of friction properties on individual contact surface. Below problematics calculation of a stiffness joint components. Using these input data is calculation minimal bolt pretension in the connection. Next part is determining inputs for joint strength check.

17 December 2019
Verified
Book Chapter
Closed access
PDF file
MTMiroslav Trochta
Miroslav Trochta
JZJiří Začal
Jiří Začal

9 October 2023 in Symmetry
Verified
Journal Article
Open access
PDF file
LHLukáš Hruzík
Lukáš Hruzík
JSJiří Struž
Jiří Struž
MTMiroslav Trochta
Miroslav Trochta
JZJiří Začal
Jiří Začal
This article deals with the uniformity of the distribution of axial forces between the individual bolts of the clamping sleeve. Clamping sleeves are machine components connecting the shaft to the hub using contact force. For sleeve pretension, bolts are used and positioned symmetrically with respect to the axis of the clamping sleeve. Though the bolts are placed symmetrically around the axis, the bolt axial forces are not uniformly distributed when the bolts are tightened according to the manufacturer’s catalog. First, this article describes the procedure for tightening the sleeve bolts according to the manufacturer’s catalog. In the next part of the article, an FEA simulation of sleeve tightening is performed. The FEM simulation is then compared with the values found by measurement.