Different infrared (IR) planar geometric calibration targets have been developed over the years that exploit a well-established and flexible optical camera geometric calibration procedure following the pinhole approximation. This geometric calibration is typically neglected in IR cameras, due to the relatively low resolution of thermal images and the complex IR targets needed for the geometric calibration in comparison to the optical targets. In this study, a thorough literature review of numerous IR camera geometric calibration targets, along with their respective outcomes, were summarized and leveraged to deliver a practical checkerboard target for less experienced end users, while offering the lowest reprojection errors. It was concluded that the fabrication of high emissivity contrast and precise square points of intersection within a checkerboard pattern extends the accuracy of capturing these control points in a thermal image for an optimized IR camera geometric calibration. Accordingly, two simple planar checkerboard targets were fabricated using laser engraving and ultraviolet (UV) printing technologies on a polished stainless steel (SS304) plate. The UV-printed checkerboard target on a polished metallic alloy delivered the lowest mean reprojection error of pixels and the lowest root mean square error of reprojection of pixels, with a standard deviation lower than pixels. The UV-printed design offers better accuracy than any other checkerboard calibration target, and comparable results to the best prominent circular pattern results reported in the literature.
17 March 2017 in Measurement Science and Technology
Eddy current spectroscopy is capable of mapping conductivities and thicknesses of layered structures due to its frequency-dependent penetration depth. High-frequency apparent eddy current conductivity (AECC) spectroscopy applications typically mandate covering a frequency range beyond 10 MHz to capture depth-dependent conductivity profiles. Following the standard four-point linear system calibration method beyond 10 MHz makes it difficult to achieve accurate AECC measurements due to spurious self- and stray-capacitive effects where complex eddy current coil impedance variation with lift-off becomes more nonlinear. In this study, two different approaches are presented to reduce AECC measurement sensitivity to lift-off. First, a nonlinear lift-off correction is developed as a function of measured apparent eddy current lift-off. Second, a semi-quadratic system calibration is developed to capture the lift-off curvature as a function of frequency and hence minimizes the measurement sensitivity to lift-off variations. Presented calibration techniques allow more robust AECC measurements up to 80–100 MHz with one-order of magnitude improvement in accuracy in comparison to the use of standard four-point linear system calibration in a lift-off range of ±25.4 µ m.
The recent coronavirus (COVID-19) pandemic has wreaked havoc on the global economy, causing major shifts in energy use and output patterns. For some countries, this has had a significant effect on energy demand and carbon emissions, at least in the short term. Since the United Arab Emirates is currently exerting many efforts towards sustainability, it is important to assess and understand the impacts of the pandemic and the lockdown measurements on the local energy sectors. Data for this analysis were gathered by the Sharjah Electricity Water & Gas Authority (SEWA) for Sharjah City which is the capital of the Emirate of Sharjah. The changes in electricity after the implementation of quarantine and lockdown-like measures were assessed, and the results indicate that the electric power demand in Sharjah City was reduced in the commercial, industrial, and agricultural sectors, whereas the residential and government sectors witnessed a higher power demand. The overall electricity consumption in the year 2020 was reduced by 1.04% in comparison with previous years including 2016 to 2019. The results of this study indicate that the changes in electricity consumption were minimal in Sharjah City as compared to other cities around the world. However, this paper highlights the importance of governmental response during and after a pandemic, and the possible impacts that lockdowns could potentially have in the energy industry worldwide.
1 February 2017 in International Journal of Applied Electromagnetics and Mechanics
Due to their high strength characteristics and excellent corrosion resistance behavior operating at different temperature ranges, titanium and nickel alloys have been gaining rapid popularity as part of weld overlay and metal spraying technologies. This has been raising the demand for a reliable and practical nondestructive evaluation technique to assess metallic coating thicknesses over nonmagnetic metals. Because of its frequency-dependent penetration depth, eddy current technology lends itself to assess such nonmagnetic layered structures. Nevertheless, impedance forward measurement techniques are sensitive to both coating/substrate conductivities and lift-off deviations from those used over the calibration blocks. This affects the accuracy and limits the capabilities of existing impedance-based inversion models in estimating coating thicknesses. This study takes the first step towards adopting AECC spectroscopy as an alternative forward measurement technique, which offers a reduced sensitivity to both deviations in a broad range of inspection frequencies. More importantly, a new AECC-based inversion algorithm is developed to estimate metallic coating thicknesses over nonmagnetic metals. This work is validated following the plane-wave approximation and COMSOL simulations over different coating thicknesses relevant to the industry.