Two shape-memory alloys with the nominal compositions (in wt.%) Cu–11.85Al–3.2Ni–3Mn and Cu–11.35Al–3.2Ni–3Mn–0.5Zr were prepared by selective laser melting (SLM). The parameters were optimised to identify the process window, in which almost fully dense samples can be obtained. Their microstructures were analysed and correlated with the shape-memory behaviour as well as the mechanical properties. Suction-cast specimens were also produced for comparison. Mainly, β1′ martensite forms in all samples, but 0.5 wt.% of Zr stabilises the Y phase (Cu2AlZr), and its morphology depends on the thermal history and cooling rate. After annealing, the Y phase is primarily found at the grain boundaries hampering grain coarsening. Due to the relative high cooling rates applied here, Zr is mostly dissolved in the martensite in the as-prepared samples and it has a grain-refining effect only up to a critical cooling rate. The Zr-containing samples have increased transformation temperatures, and the Y phase seems to be responsible for the jerky martensite-to-austenite transformation. All the samples are relatively ductile because they mostly fracture in a transgranular manner, exhibiting the typical double yielding. Selective laser melting allows the adjustment of the transformation temperatures and the mechanical properties already during processing without the need of a subsequent heat treatment.
A NiTi shape memory alloy with the nominal composition Ni50.9Ti49.1 (at%) was processed by laser beam melting/laser powder bed fusion and the process parameters as well as the type of scanning strategy (point-like exposure) were optimized in a first step to obtain delicate lattice structures (strut diameters below 200 µm). In the second step, the lattice structures were analyzed by means of optical and electron microscopy as well as computer tomography to obtain the interrelation between the process parameters, strut diameter and the uniformity of the corresponding struts. The processing, especially the laser power and the type of point-like exposure, has a strong influence on the resulting strut diameter and, therefore, on the haptic stiffness of lattice structures and the mechanical properties (deformability, superelasticity). Unlike other approaches, our findings imply that filigree NiTi lattices with high uniformity can be manufactured on a standard industry laser powder bed fusion machine without modifying its hard- or software configuration.
In order to overcome constraints related to crack formation during additive processing (laser powder bed fusion, L-BPF) of Fe-Mn-Al-Ni, the potential of high-temperature L-PBF processing was investigated in the present study. The effect of the process parameters on crack formation, grain structure, and phase distribution in the as-built condition, as well as in the course of cyclic heat treatment was examined by microstructural analysis. Optimized processing parameters were applied to fabricate cylindrical samples featuring a crack-free and columnar grained microstructure. In the course of cyclic heat treatment, abnormal grain growth (AGG) sets in, eventually promoting the evolution of a bamboo like microstructure. Testing under tensile load revealed a well-defined stress plateau and reversible strains of up to 4%.
This study focuses on the influence of additive manufacturing process strategies on the specimen geometry, porosity, microstructure and mechanical properties as well as their impacts on the design of metamaterials. Filigree additively manufactured NiTi specimens with diameters between 180 and 350 µm and a nominal composition of Ni50.9Ti49.1 (at %) were processed by laser powder bed fusion in a first step. Secondly, they structures were characterized by optical and electron microscopy as well as micro tomography to investigate the interrelations between the process parameters, specimen diameters and microstructure. Each specimen was finally tested in a micro tensile machine to acquire the mechanical performance. The process strategy had, besides the resulting specimen diameter, an impact on the microstructure (grain size) without negatively influencing its quality (porosity). All specimens revealed a superelastic response while the critical martensitic phase transition stress decreased with the applied vector length. As a conclusion, and since the design of programmable metamaterials relies on the accuracy of FEM simulations, precise and resource-efficient testing of filigree and complex structures remains an important part of creating a new type of metamaterials with locally adjusted material behavior.