To develop an effective pH-sensitive drug carrier, alginate (Alg), carboxymethyl chitosan (CMCs), and aminated chitosan (AmCs) derivatives were employed in this study. A simple ionic gelation technique was employed to formulate Alg-CMCs@AmCs dual polyelectrolyte complexes (PECs) microcapsules as a pH-sensitive carrier for efficient encapsulation and release of diclofenac sodium (DS) drug. The developed microcapsules were characterized by Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analyzer (TGA), and scanning electron microscope (SEM). The results clarified that formation of dual PECs significantly protected Alg microcapsules from rapid disintegration at colon conditions (pH 7.4), and greatly reduced their porosity. In addition, the dual PECs microcapsules can effectively encapsulate 95.4% of DS-drug compared to 86.3 and 68.6% for Alg and Alg-CMCs microcapsules, respectively. Higher DS-release values were achieved in simulated colonic fluid [SCF; pH 7.4] compared to those obtained in simulated gastric fluid [SGF; pH 1.2]. Moreover, the drug burst release was prevented and a sustained DS-release was achieved as the AmCs concentration increased. The results confirmed also that the developed microcapsules were biodegradable in the presence of the lysozyme enzyme. These findings emphasize that the formulated pH-sensitive microcapsules could be applied for the delivery of diclofenac sodium.
This study intends to provide new TiO2/phosphorous-functionalized cellulose acetate (Ph-CA) nanocomposite membranes for direct methanol fuel cells (DMFCs). A series of TiO2/Ph-CA membranes were fabricated via solution casting technique using a systematic variation of TiO2 nanoparticle content. Chemical structure, morphological changes, and thermal properties of the as-fabricated nanocomposite membranes were investigated by FTIR, TGA, SEM, and AFM analysis tools. Further, membranes’ performance, mechanical properties, water uptake, thermal-oxidative stability, and methanol permeability were also evaluated. The results clarified that the ion-exchange capacity (IEC) of the developed nanocomposite membranes improved and reached a maximum value of 1.13 and 2.01 meq/g at 25 and 80 °C, respectively, using TiO2 loading of 5 wt % compared to 0.6 and 0.81 meq/g for pristine Ph-CA membrane at the same temperature. Moreover, the TiO2/Ph-CA nanocomposite exhibited excellent thermal stability with appreciable mechanical properties (49.9 MPa). The developed membranes displayed a lower methanol permeability of 0.98 × 10–16 cm2 s–1 compared to 1.14 × 10–9 cm2 s–1 for Nafion 117. The obtained results suggested that the developed nanocomposite membranes could be potentially applied as promising polyelectrolyte membranes for possible use in DMFCs.
Herein, graphene oxide nanosheets (GO) were synthesized and employed as an additive at various proportions to fabricate a novel cation exchange membrane based on grafted cellulose acetate with sodium 4-styrenesulfonate (GCA) via a solution casting method for direct methanol fuel cell (DMFC) applications. The structure of composite membranes has been examined using FTIR, TGA, SEM, and DSC. The physicochemical properties of the GCA/GO membranes, such as ion exchange capacity, water uptake, mechanical and chemical stability, methanol permeability, and proton conductivity, were measured. The inclusion of GO significantly improved the ability to block methanol, contributing to the observed effects. Among the several composite membranes developed, GCA/GO (2 wt.%) had the highest selectivity with a water uptake of 45%, proton conductivity of 5.99 × 10−3 S/cm, methanol permeability of 1.12 × 10−7 cm2/s, and electrical selectivity of 26.39 × 103 Ss/cm3. Simultaneously, the composite membranes’ mechanical, oxidative, and thermal stabilities were also enhanced. Single-cell estimation using a 2 wt.% GO modified membrane demonstrated a maximum power density of 31.85 mW.cm−2 at 30 °C. Overall, these findings highlight the perspective of the application of these developed membranes in the DMFC.
13 November 2024 in The International Journal of Advanced Manufacturing Technology
Three-dimensional printing (3DP) is a technology useful for fabricating both structural and energy devices. Of great concern to this review is promising nature of additive manufacturing (AM) for engineering fuel cells (FCs) for clean energy conversion. 3DP technique is useful for the fabrication of fuel cell components, and they offer waste minimization, low-cost, and complex geometric structures. In this review, significance of different 3DP techniques toward revolutionizing fuel cell fabrication is given. The aim is to unravel the importance and status of 3D-printed fuel cells and hence provides researchers and scientists with extensive opportunities of 3DP techniques for fuel cell engineering. After careful selection of state-of-the-art literatures, different kinds of 3DP techniques of relevance to electrolytes, electrodes, and other key components (e.g., gas diffusion layers (GDLs), bipolar plates (BPs), and membrane electrode assembly (MEA)) fabrication are explicitly discussed. Among the techniques, the best approaches are recommended for further studies. Advantages associated with these techniques are indicated for the benefit of those whose interests matter most on clean energy production. The challenges researchers are facing in the use of 3DP for fuel cell fabrications are identified. Possible solutions to the identified challenges are suggested as way forward to further development in this research area. It is expected that this review article will benefit engineers and scientists who have interest on clean energy conversion devices.
2 May 2023 in Journal of Drug Delivery Science and Technology