Andrew Nabil Aziz Makar

Dr. Andrew Nabil Aziz Makar

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 January 2020 in Frontiers in Materials
Verified
Journal Article
Open access
PDF file
MGMarwa Gouda
Marwa Gouda
MEMohamed Elnouby
Mohamed Elnouby
AMAndrew Nabil Aziz Makar
Andrew Nabil Aziz Makar
Mohamed Elsayed Aly YoussefMohamed Elsayed Aly Youssef
Mohamed Elsayed Aly Youssef
Diogo M.F. SantosDiogo M.F. Santos
Diogo M.F. Santos
Noha ElessawyNoha Elessawy
Noha Elessawy
The success of fuel cells depends on the proper design of the electrodes and membrane allowing easy access of oxygen and protons. Using non-precious catalyst electrodes based on recyclable carbon nanostructures is most important to produce clean energy and increase the ability to commercialize the fuel cells. Herein, reduced graphene oxide (rGO) and graphene/magnetic iron oxide nanocomposite (rGO/MIO) are successfully synthesized as anode and cathode, respectively, from polyethylene terephthalate (PET) waste bottles using easy steps in order to simplify the method and reducing the production cost. While, the membrane is prepared from low cost and eco-friendly ternary polymers blend which are polyvinyl alcohol (PVA), polyethylene oxide (PEO) and polyvinyl pyrrolidone (PVP) then doped with sulfonated graphene oxide. The prepared electrodes have characteristic high porosity and their electrocatalytic performances are evaluated using three-electrode cell electrochemical studies as cyclic voltammetry and linear scan voltammetry combined with rotating disk electrode. A new assembly of the membrane between two non-precious catalyst electrodes as a single polymer electrolyte membrane fuel cell (PEMFC) was developed using a catalyst-coated membrane technique. The membrane electrode assembly (MEA) design parameters which affect its performance in hydrogen fuel cells as number of used catalyst layers (CL) or using gas diffusion layer (GDL) were evaluated in a single cell set-up with H2/O2 operation and the results revealed that the performance MEA was enhanced with using GDL more than that of MEA without GDL by 66% at a current density of 0.8 A cm−2 while the performance with double CL was better than that of the conventional single CL by 30% at a current density of 0.98 mA cm−2.

3 July 2022 in Applied Thermal Engineering
Verified
Journal Article
Closed access
AMAndrew Nabil Aziz Makar
Andrew Nabil Aziz Makar
SMSaad Mahmoud
Saad Mahmoud
RARaya Al-Dadah
Raya Al-Dadah
MIMohamed Anwar Ismail
Mohamed Anwar Ismail
Mohammed K AlmesferMohammed K Almesfer
Mohammed K Almesfer

8 July 2024 in Energy
Verified
Journal Article
Closed access
AMAndrew Nabil Aziz Makar
Andrew Nabil Aziz Makar
SMSaad Mahmoud
Saad Mahmoud
RARaya Al-Dadah
Raya Al-Dadah
ATAnil Taskin
Anil Taskin
MIMohamed A. Ismail
Mohamed A. Ismail
MRMamoon Rashid
Mamoon Rashid

22 January 2023 in Processes
Verified
Journal Article
Open access
PDF file
ASAsmaa Attya Shalaby
Asmaa Attya Shalaby
AMAndrew Nabil Aziz Makar
Andrew Nabil Aziz Makar
Zdenko SpitalskyZdenko Spitalsky
Zdenko Spitalsky
Ahmed M. OmarAhmed M. Omar
Ahmed M. Omar
Mohamed Samir MohyeldinMohamed Samir Mohyeldin
Mohamed Samir Mohyeldin
RGRanda Khalifa Ghonim
Randa Khalifa Ghonim
Herein, graphene oxide nanosheets (GO) were synthesized and employed as an additive at various proportions to fabricate a novel cation exchange membrane based on grafted cellulose acetate with sodium 4-styrenesulfonate (GCA) via a solution casting method for direct methanol fuel cell (DMFC) applications. The structure of composite membranes has been examined using FTIR, TGA, SEM, and DSC. The physicochemical properties of the GCA/GO membranes, such as ion exchange capacity, water uptake, mechanical and chemical stability, methanol permeability, and proton conductivity, were measured. The inclusion of GO significantly improved the ability to block methanol, contributing to the observed effects. Among the several composite membranes developed, GCA/GO (2 wt.%) had the highest selectivity with a water uptake of 45%, proton conductivity of 5.99 × 10−3 S/cm, methanol permeability of 1.12 × 10−7 cm2/s, and electrical selectivity of 26.39 × 103 Ss/cm3. Simultaneously, the composite membranes’ mechanical, oxidative, and thermal stabilities were also enhanced. Single-cell estimation using a 2 wt.% GO modified membrane demonstrated a maximum power density of 31.85 mW.cm−2 at 30 °C. Overall, these findings highlight the perspective of the application of these developed membranes in the DMFC.

1 May 2023 in Energies
Verified
Journal Article
Open access
PDF file
AMAndrew Nabil Aziz Makar
Andrew Nabil Aziz Makar
Raya Al-DadahRaya Al-Dadah
Raya Al-Dadah
SMSaad Mahmoud
Saad Mahmoud
MIMohamed A. Ismail
Mohamed A. Ismail
Mohammed K AlmesferMohammed K Almesfer
Mohammed K Almesfer
HSHassan shokry
Hassan shokry
Greenhouses with efficient controlled environment offer a promising solution for food security against the impacts of increasing global temperatures and growing water scarcity. However, current technologies used to achieve this controlled environment consume a significant amount of energy, which impacts on operational costs and CO2 emissions. Using advanced metal organic framework materials (MOFs) with superior water adsorption characteristics, this work investigates the development of a new technology for a greenhouse-controlled environment. The system consists of MOF coated heat exchanger, air to air heat exchanger, and evaporative cooler. A three-dimensional computational fluid dynamics (CFD) model was developed using COMSOL software and experimentally validated for the MOF-801/Graphene coated heat exchanger (DCHE) to determine the best cycle time and power input. It was found that using desorption time of 16 min and power input of 1.26 W, the maximum water removal rate was obtained from MOF-801/Graphene of 274.4 g/kgMOF/W.hr. In addition, an overall mathematical model for the greenhouse climate control was developed and used to investigate the effects of air humidity and velocity on the input air conditions to the greenhouse. Results showed that with high relative humidity levels of 90% in the greenhouse can be conditioned to reach the required relative humidity of 50%.