Lignin was isolated from wood wastes comprising Iroko sawdust (IR) and mixed sawdust from Iroko and Norway spruce (IRNS), furnished by a local wood houses producer. The respective acidolysis lignin fractions were structurally characterized using pyrolysis (Py)-GCMS, two-dimensional heteronuclear single quantum correlation nuclear magnetic resonance (2D HSQC NMR), Fourier-transform infrared FTIR and ultraviolet-visible (UV-VIS) spectroscopies, size exclusion chromatography, and standard wet-chemistry methods for Klason lignin and polysaccharides determination. The isolated lignin fractions were subsequently used for the preparation of lignin nanoparticles (LNPs) using a non-solvent method. LNPs were then used for wood surface treatment using a dip-coating technique. The coated wood samples were analyzed by colorimetry and scanning electron microscopy (SEM) before and after artificial weathering experiments in a UV chamber to investigate the UV protection potential of the LNPs coatings. Wood samples dip-coated with LNPs showed promising surface modifications resembling a sort of film of fused LNPs. Coatings made from IR-LNPs and IRNS-LNPs performed significantly better in artificial weathering experiments than uncoated reference samples.

Three different formulations of bio-based polyurethane (PU), varying the weight ratio between Organosolv lignin and a commercial isocyanate, were synthesized. The coating formulations were characterized by SEM, pyrolysis-GC/MS, FTIR spectroscopy and FTIR mapping, which confirmed the successful formation of urethane bonds between commercial isocyanate and hydroxyl groups deriving from lignin. The coatings were applied on beech wood samples to measure color and contact angles, and eventually FTIR mapping of the coated wood samples was performed. FTIR mapping is an interesting tool to monitor the distribution of PU chemical bonds on the coating surface and to evaluate the homogeneity of the applied coating films. Increasing the lignin content of the PU coatings results in more red-yellow and darker tones, while the commercial PU coating is transparent. For a higher lignin concentration, the solid content as well as the weight gain of the applied coatings increase. A higher percentage of lignin in the prepared PU formulations leads to superficial cracks and therefore higher coating permeability compared to the commercial PU, but the prepared lignin-based PU coating still makes a raw wood surface significantly more hydrophobic. Apparently, additives such as film-formers with low surface tension to counteract cracks’ formation are necessary to improve the performance of lignin-based PU coatings.

Stinging nettle (Urtica dioica L.) is a ubiquitous, multi-utility, and under-utilized crop with potential health benefits owing to its nutritional and bioactive components. The objective of the work is to produce powders by drying wild stinging nettle leaves as a storable, low-cost functional additive to be used in bakery and ready-to-cook products. Convective drying (CD) and freeze-drying (FD) were applied on unblanched (U) or blanched (B) leaves, which were then milled to nettle powders (NPs). The obtained NPs were evaluated for selected physicochemical (moisture, color), techno-functional (flow indices, hygroscopicity), and phytochemical (pigments, phenols) characteristics as well as mineral contents. Blanching improved mass transfer and reduced the oxidative degradation of pigments during drying, but it caused a loss of total phenols content, antioxidant activity, and potassium content. As for the drying method, CD resulted in better flow properties (i.e., Carr Index and Hausner Ratio), while FD retained better the color, pigments, magnesium content, phenolic, and antioxidant parameters. Overall, the evaluated processing methods resulted in different technological properties that can allow for better evaluation of NPs as a food additive or ingredient. Among the NPs, blanched and freeze-dried powders despite showing inferior technological properties can be recommended as more suitable ingredients targeted f or food enrichment owing to better retention of bio-active components.

Acidolysis lignins from the species Quercus cerris L. and Eucalyptus camaldulensis Dehnh. were isolated and characterized using high pressure size exclusion chromatography (HP-SEC), Fourier-transform (FTIR) infrared spectroscopy, analytical pyrolysis–gas chromatography–mass spectrometry (Py-GCMS), and two-dimensional heteronuclear single quantum coherence (2D HSQC) NMR spectroscopy. The acidolysis lignins from the two different species varied in chemical composition and structural characteristics, with Q. cerris L. lignin having a higher S/G ratio and higher molar mass averages with a bimodal molar mass distribution. The different analytical techniques FTIR spectroscopy, Py-GCMS, and 2D NMR spectroscopy provided consistent results regarding the S/G ratio of the lignins from the two wood species. Based on the determined high S/G ratio of both oak and eucalypt lignin, the two wood sources could be promoted as substrates for efficient lignin isolation in modern forest biorefineries in order to develop innovative lignin-based value-added biorefinery products.

Sustainability and ecotoxicity issues call for innovations regarding eco-friendly adhesives in the production of biocomposite wood materials, and solutions involving nano-scale and bio-based compounds represent a valid and promising target. One possible approach is to increase the performance of adhesives such as polyvinyl acetate (PVAc) or melamine-urea-formaldehyde (MUF) by means of nanoparticles in order to obtain a material with better mechanical and environmental resistance. When applying cellulose-based nanoparticles or tannin, the concept of a circular economy is successfully implemented into the forest/wood value chain, and chances are created to develop new value chains using byproducts of forestry operations. In this study, assortments coming from young sweet chestnut (Castanea sativa Mill.) coppice stands were utilized for the preparation of single lap joint assemblies using different commercial adhesives (PVAc, MUF) and cellulose nanocrystals (CNC) and tannin as additives. The results showed that addition of CNC and tannin to PVAc glue increased tensile shear strength in lap joint tests presenting a promising base for future tests regarding the addition of CNC and tannin in MUF or PVAc adhesive formulations. Unfortunately, the tested bio-based additives did not reveal the same encouraging results when tested in the wet state.