Ali Riahi

Dr. Ali Riahi


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 August 2024 in npj Materials Degradation
Verified
Journal Article
Open access
PDF file
DWD. C. Williams
D. C. Williams
ARAli Riahi
Ali Riahi
ACA. Carcea
A. Carcea
JGJ. D. Giallonardo
J. D. Giallonardo
PKP. Keech
P. Keech
RNRoger Newman
Roger Newman
Slow strain rate tensile testing was conducted on electrodeposited copper, which is a candidate coating material for used nuclear fuel containers. Embrittlement was observed in electrodeposited copper containing 26.4 ± 1.0 ppm hydrogen, with a strain rate sensitivity such that the embrittlement was exacerbated at lower strain rate (5 × 10−7 s−1). Tensile tests conducted at 100° and 200 °C also intensified embrittlement when compared with tests conducted at room temperature. In contrast, electrodeposited copper containing only 5.25 ± 0.97 ppm hydrogen exhibited ductile behavior at all tested strain rates and temperatures. These findings suggest that a previously unexplained slow strain rate hydrogen embrittlement can operate in electrodeposited copper provided that the hydrogen concentration is sufficiently high. Further analyses revealed that the deformation of embrittled copper is achieved by the formation of internal microcracks which coalesce at the point of failure.

12 January 2022 in Journal of Modern Optics
Verified
Journal Article
Closed access
ARAli Riahi
Ali Riahi
MVMohammad Vahedi
Mohammad Vahedi
In this study, extensive research has been carried out to determine the optimum geometry resulting in the highest sensitivity for the tapered fibre-optic sensors in a broad geometrical range. A staircase concatenation method was introduced to investigate the effect of the taper angle and diameter on the sensor’s sensitivity. The results show that the sensor’s sensitivity increases by reducing the taper diameter. Moreover, the effect of the tapering angle on the sensitivity has an optimum point. As a result, there is an optimum taper curvature for exponential-linear profiles, which results in the highest sensitivity. Indeed, it was revealed that the sensitivity changes versus taper diameter and angle could be justified considering the coupled power to different modes of the tapered fibre as well as the ratio of the power outside the fibre taper to the total power for different modes.

1 June 2017 in Optik
Verified
Journal Article
Closed access
SFSina Foroutan
Sina Foroutan
HDHossein Zaki Dizaji
Hossein Zaki Dizaji
ARAli Riahi
Ali Riahi

28 December 2021 in Corrosion
Verified
Journal Article
Closed access
PDF file
ARAli Riahi
Ali Riahi
ACAnatolie G. Carcea
Anatolie G. Carcea
RNRoger C. Newman
Roger C. Newman
This work aims to illuminate localized carbon steel corrosion in ethanolic solutions. The effect of chloride, ethanol dehydration, and oxygen level are investigated, which all play a role in the carbon steel pitting behavior in ethanolic environments in the presence of a supporting electrolyte. Open-circuit potential measurement, cyclic potentiodynamic polarization, and potentiostatic testing are conducted on specimens exposed to ethanolic environments prepared from pure dehydrated ethanol to study the pitting behavior of carbon steel. Corrosion and passivation potentials are found to be significantly reduced due to the change in the cathodic reaction and the decrease in passivation kinetics under deaerated conditions. Energy-dispersive x-ray spectroscopy examination and scanning electron microscopy imaging indicate that no pitting corrosion is observed without chlorides, and chloride significantly destabilizes the surface film, resulting in the reduction of both pitting potential and passivation potential. Increasing the amount of dissolved oxygen in the solution reduces pitting susceptibility and, in low chloride concentrations, can eliminate the pitting nucleation. Iron oxide is identified as the significant corrosion product at different water and oxygen concentrations. Therefore, ethanol aeration can be an effective method to increase resistance to pitting corrosion in ethanolic solutions. Aeration can be used with caution due to the effect of oxygen on steel stress corrosion cracking in ethanol.

8 January 2020 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
ARAli Riahi
Ali Riahi
AFAmir Foroozanebrahimy
Amir Foroozanebrahimy
MGMahmoudreza Ghaznavi
Mahmoudreza Ghaznavi
Ali SeifitokaldaniAli Seifitokaldani
Ali Seifitokaldani
RNRoger C. Newman
Roger C. Newman
Striking mechanical and morphological similarities of the stress corrosion cracking (SCC) of carbon steel in ethanolic media with those governed by a cleavage-like mechanism in CO-CO2 aqueous solutions, prompted the investigation of the possibility of ethanol electrochemical oxidation into CO on ferrite (Fe) and cementite (Fe3C) surfaces. Density functional theory computations on (110) surfaces reveal that the catalytic activity of Fe and Fe3C through the α dehydrogenation pathway can significantly reduce the energy barrier of electro-oxidation of ethanol and production of CO to 0.575 and 0.480 eV, respectively. These first principle calculations indicate that at the anodic potentials applied during potentiostatic slow strain rate testing, ethanol electrooxidation to CO is thermodynamically viable on carbon steel, giving further credit to the involvement of cleavage type SCC of carbon steel in ethanolic environments.

20 July 2020 in Materials and Corrosion
Verified
Journal Article
Closed access
PDF file
ARAli Riahi
Ali Riahi
AEAmir Forrozan Ebrahimy
Amir Forrozan Ebrahimy
VRVindel Ramsundar
Vindel Ramsundar
AKAndreas Korinek
Andreas Korinek
RNRoger Newman
Roger Newman