Capacitorlike metal/metal oxide/metal structures are widely used as resistive switching cells and are utilized in resistive random access memories. Recently, it has been demonstrated that they also perform well as gas sensors. In this work, we have merged the gas sensing and resistive switching capabilities of the capacitorlike Pt/TiO2/Pt structures to constitute a simple device which works as a gas-triggered thyristorlike switch and as a gas sensor with a built-in memory.
Due to the increased demands for drilling and cutting tools working at extreme machining conditions, protective coatings are extensively utilized to prolong the tool life and eliminate the need for lubricants. The present work reports on the effect of a second MeN (Me = Zr, Cr, Mo, Nb) layer in WN-based nanocomposite multilayers on microstructure, phase composition, and mechanical and tribological properties. The WN/MoN multilayers have not been studied yet, and cathodic-arc physical vapor deposition (CA-PVD) has been used to fabricate studied coating systems for the first time. Moreover, first-principles calculations were performed to gain more insight into the properties of deposited multilayers. Two types of coating microstructure with different kinds of lattices were observed: (i) face-centered cubic (fcc) on fcc-W2N (WN/CrN and WN/ZrN) and (ii) a combination of hexagonal and fcc on fcc-W2N (WN/MoN and WN/NbN). Among the four studied systems, the WN/NbN had superior properties: the lowest specific wear rate (1.7 × 10−6 mm3/Nm) and high hardness (36 GPa) and plasticity index H/E (0.93). Low surface roughness, high elastic strain to failure, Nb2O5 and WO3 tribofilms forming during sliding, ductile behavior of NbN, and nanocomposite structure contributed to high tribological performance. The results indicated the suitability of WN/NbN as a protective coating operating in challenging conditions.
Plasma catalysis has been utilized in many environmental applications for removal of various hydrocarbons including tars. The aim of this work was to study the tars removal process by atmospheric pressure DBD non-thermal plasma generated in combination with packing materials of various composition and catalytic activity (TiO2, Pt/γAl2O3, BaTiO3, γAl2O3, ZrO2, glass beads), dielectric constant (5–4000), shape (spherical and cylindrical pellets and beads), size (3–5 mm in diameter, 3–8 mm in length), and specific surface area (37–150 m2/g). Naphthalene was chosen as a model tar compound. The experiments were performed at a temperature of 100 °C and a naphthalene initial concentration of approx. 3000 ppm, i.e., under conditions that are usually less favorable to achieve high removal efficiencies. For a given specific input energy of 320 J/L, naphthalene removal efficiency followed a sequence: TiO2 > Pt/γAl2O3 > ZrO2 > γAl2O3 > glass beads > BaTiO3 > plasma only. The efficiency increased with the increasing specific surface area of a given packing material, while its shape and size were also found to be important. By-products of naphthalene decomposition were analyzed by means of FTIR spectrometry and surface of packing materials by SEM analysis.
The present work investigates the influence of isothermal annealing on the microstructure and oxidation behavior of nanocomposite coatings. AlTiSiN/TiSiN coatings with TiSiN adhesive layer were deposited onto a high-speed steel substrate via physical vapor deposition. The coatings were investigated in the as-deposited state as well as after annealing in air at 700, 800, 900 and 1000 °C, respectively. The microstructure and morphology of the coatings were observed using scanning electron microscopy and transmission electron microscopy. The chemical composition and presence of oxidation products were studied by energy-dispersive X-ray spectroscopy. The phase identification was performed by means of X-ray diffraction. In the microstructure of the as-deposited coating, the (Ti1−xAlx)N particles were embedded in an amorphous Si3N4 matrix. TiO2 and SiO2 were found at all annealing temperatures, and Al2O3 was additionally identified at 1000 °C. It was found that, with increasing annealing temperature, the thickness of the oxide layer increased, and its morphology and chemical composition changed. At 700 and 800 °C, a Ti-Si-rich surface oxide layer was formed. At 900 and 1000 °C, an oxidized part of the coating was observed in addition to the surface oxide layer. Compared to the as-deposited sample, the oxidized samples exhibited considerably worse mechanical properties.